Abstract:With the advantages of a high theoretical capacity, proper working voltage, and abundant reserves, silicon (Si) is regarded as a promising anode for lithium-ion batteries. However, huge volume expansion and low electronic conductivity impede the commercialization of Si anodes. We devised a one-step, vacuum-assisted reactive carbon coating technique to controllably produce micrometer-sized nanoporous silicon confined by homogeneous N-doped carbon nanosheet frameworks (), achieved by the solid state reaction of a commercial bulk precursor and the subsequent evaporation of byproducts. The graphitization degree, C and N contents of the carbon shell, as well as the porosity of Si can be regulated by adjusting the synthetic conditions. A rational structure can mitigate volume expansion to maintain structural integrity, enhance electronic conductivity to facilitate charge transport, and serve as a protected layer to stabilize the solid electrolyte interphase. The anode enables a stable cycling performance with 95.68% capacity retention for 4000 cycles at 5 A g–1. Furthermore, a flexible 2D/3D architecture is designed by conjugating with MXene. Lithiophilic homogenize Li nucleation and growth, evidenced by structural evolutions of @NCNF deposited Li. The application potential of and @NCNFs is estimated via assembling full cells with LiNi0.8Co0.1Mn0.1O2 and LiNi0.5Mn1.5O4 cathodes. This work offers a method for the rational design of alloy-based materials for advanced energy storage.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acsnano.1c11098.Experimental section; XRD pattern and XPS spectra of Mg2Si and C3N4; ID/IG values, C and N contents, N2 adsorption/desorption isotherms, pore size distributions, TEM, HRTEM, and SAED of ; XRD, XPS, SEM and EDS mapping images of Nano-Si; charge/discharge curves of Nano-Si and anodes for LIBs at different rates; digital photograph (electrode and separator), SEM, thickness and thickness changes of Nano-Si and anodes before and after cycles; GITT and diffusion coefficients of and ; XRD, SEM, and EDS mapping images of NCM and LNMO; charge/discharge curves and capacity retentions of a full cell with Nano-Si and anodes at different rates (NCM and LNMO cathodes); EIS curves of a cycled full cell with Nano-Si and anodes (NCM and LNMO cathodes); XRD, SEM, and EDS mapping images of MAX; digital photograph of MXene solution; XRD, Raman, XPS, SEM, EDS mapping images, and digital photograph of MXene; SEM of @NCNFs; SEM of structural evolutions of Cu foil and @NCNFs deposited Li with different area capacities; voltage profiles on Cu and @NCNFs; EIS and SEM of Cu, @NCNFs, , and @ for Li metal anode after cycles; charge/discharge curves and capacity retentions of a full cell with and @ anodes at different rates (NCM and LNMO cathodes); EIS curves of a cycled full cell with and @ anodes (NCM and LNMO cathodes) (PDF)This article has not yet been cited by other publications.

Prelithiated Li-Enriched Gradient Interphase toward Practical High-Energy NMC–Silicon Full Cell

One-Step, Vacuum-Assisted Construction of Micrometer-Sized Nanoporous Silicon Confined by Uniform Two-Dimensional N-Doped Carbon toward Advanced Li Ion and MXene-Based Li Metal Batteries

High-Ni NMC Cathode Material with Concentration Gradients in Lithium-Ion Batteries

Gradient-porous-structured Ni-rich Layered Oxide Cathodes with High Specific Energy and Cycle Stability for Lithium-Ion Batteries

Scalable Synthesis of Si Nanosheets as Stable Anodes for Practical Lithium-Ion Batteries

Stabilizing the Bulk-Phase and Solid Electrolyte Interphase of Silicon Microparticle Anode by Constructing Gradient-Hierarchically Ordered Conductive Networks

Enabling high energy lithium metal batteries via single-crystal Ni-rich cathode material co-doping strategy

Tailoring of Gradient Particles of Li-Rich Layered Cathodes with Mitigated Voltage Decay for Lithium-Ion Batteries

“Nano-Skeleton” Si-SiOx@C Anodes towards Highly Stable Lithium-ion Batteries

Prelithiating Si-Based Anodes using Li-Excess Layered Positive Electrode Materials

Engineering Nano-Sized Silicon Anodes with Conductive Networks Toward a High Average Coulombic Efficiency of 90.2% Via Plasma-Assisted Milling

Tuning the Interface Stability of Nickel-Rich NCM Cathode Against Aggressive Structural Collapse via the Synergistic Effect of Additives

Interfacial nitrogen engineering of robust silicon/MXene anode toward high energy solid-state lithium-ion batteries

High-performance Self-Organized Si Nanocomposite Anode for Lithium-Ion Batteries

Large-Scale Electric-Field Confined Silicon with Optimized Charge-Transfer Kinetics and Structural Stability for High-Rate Lithium-Ion Batteries

Rational Electrolyte Design to Form Inorganic–Polymeric Interphase on Silicon-Based Anodes

Fabrication and Performance of High Energy Li-Ion Battery Based on the Spherical Li[Li0.2Ni0.16Co0.1Mn0.54]O2 Cathode and Si Anode

An Anode Material for Lithium Storage: Si@N,S-Doped Carbon Synthesized via In Situ Self-Polymerization

A Bifunctional-Modulated Conformal Li/Mn-Rich Layered Cathode for Fast-Charging, High Volumetric Density and Durable Li-Ion Full Cells

A High-Efficient Stable Surface-Prelithiated Li1.2ni0.13co0.13mn0.54o2 Cathode Enabled by Sacrificial Lithium Nitrides for High-Energy-Density Lithium-Ion Batteries

Two-Dimensional Silicon/Carbon from Commercial Alloy and CO 2 for Lithium Storage and Flexible Ti 3 C 2 T x MXene-Based Lithium–Metal Batteries