Abstract:Square-small holes are used as a critical feature in the fields of aerospace, machine-tooling, automation, and mechanical component construction. Electrochemical drilling (EC-drilling) is a promising approach for manufacturing square-small holes. However, the distribution of flow field in the inter-electrode gap (IEG) becomes non-uniform because of the unique structure of the square-cross-section tubular tool, leading to the accumulation of electrolytic by-products in the IEG. Consequently, both shape accuracy and machining efficiency are reduced. This paper proposes an EC-drilling process with workpiece vibration, in which low-frequency vibration is applied to the workpiece and the size of the frontal IEG is periodically altered. This approach can improve the flow field distribution and eliminate constant low flow velocity zones, resulting in enhanced mass transfer in the IEG. A 3D computational fluid dynamics (CFD) model includes discrete phase was developed to analyze the characteristics of the flow field and elucidate the enhancement mechanism of workpiece vibration in the transfer process. Simulation results revealed that a pulsating electrolyte flow field was produced in both frontal and side IEG induced by workpiece vibration, and that high flow velocity zones were generated alternately in frontal IEG and side IEG. With minimum frontal IEG, there was a high flow velocity in frontal IEG, with parcels (each parcel contains 205 particles) being transported smoothly from frontal IEG to the side IEG. High flow velocity switched to the side IEG when frontal IEG was maximum, and parcels that accumulated in the side IEG were easily removed. With the workpiece vibration process repeated, the parcel transfer process in the IEG was enhanced and the number of parcels accumulating in the IEG significantly reduced. The enhancement of workpiece vibration on the machining of square-small hole was verified by experiments, reflected as enhancement in both the surface quality and shape accuracy of square-small holes. Increasing both the vibration amplitude and frequency enhanced the removal rate of electrolytic by-products, thereby improving machining quality. Machining quality was further improved using a high pulse frequency and low pulse duty cycle. With appropriate parameters, the maximum cathode feed rate reached 1.44 mm/min, 2.4 times that previously reported, and the width and corner radius of the square-small hole was 1.16 mm ± 0.003 mm and 149 μm, respectively, with a surface roughness of 0.54 μm on the sidewall of the square-small hole.

Advancing electrochemical drilling process via coupling of flow field and electric field in pulsating state generated by a novel tube tool

Enhancement mechanism of electrochemical drilling square-small holes with workpiece vibration

Electrochemical milling of deep-narrow slots with a pulsating electrolyte flow field

Electrochemical Machining of Hole Structures by Using Superhydrophobic Tube Electrode

Electrochemical drilling of small holes by regulating in real-time the electrolyte flowrate in multiple channels

Performance improvement of high-speed EDM and ECM combined process by using a helical tube electrode with matched internal and external flushing

Wire Electrochemical Machining with Pulsating Radial Electrolyte Supply and Preparation of Its Tube Electrode with Micro-Holes

Effects of Helical Tube Electrode Structure on Mixed Machining Product Transfer in Micro-Machining Channel during Tube Electrode High-Speed Electrochemical Discharge Machining

Formation and reduction of taper in electrochemical single-pass milling grooves

Dielectric Flushing Optimization of Fast Hole EDM Drilling Based on Debris Status Analysis

Theoretical and experimental study on micro ultrasonic-assisted electrochemical drilling with high speed electrode

Workpiece vibration in feed direction assisted electrochemical cutting using tube electrode with inclined holes

Investigation of the Material Removal Mechanism in Electrochemical Discharge Drilling Using a High-Speed Rotating Helical Tool-Electrode

Analysis of Multi-Physics Coupling of Small Holes in GH4169 Alloy by Electrolytic Processing of Tube Electrodes

Research on machining Technology of Electrospark-electrochemical Hybrid Energy Field with tungsten hole

Machining performance enhancement of deep micro drilling using electrochemical discharge machining under magnetohydrodynamic effect

Research on Multi-physics Field Coupling Dynamic Process in Forward Flow Electrochemical Trepanning Blades

Interelectrode gas–liquid-solid three-phase flow analysis and simulation for drilling holes with high aspect ratio by micro-EDM

Fabrication of Ultra-Fine and Ultra-Long Copper Tube Electrodes by Ultrasonic High-Frequency Percussion

A novel EDM method using longitudinal-torsional ultrasonic vibration (LTV) electrodes to improve machining performance for micro-holes

Electrical discharge drilling of blind holes with injection flushing dielectric and stepped electrodes