Abstract:The main objective of this research was to investigate the effect of adding CuO (2 wt.%) nanoparticles and changing the cooling rate on the microstructure and mechanical properties of Al (2 wt.%) Si. The addition of CuO nanoparticles to Al-2wt.%Si (alloy A) resulted in a composite alloy (alloy B). Optical microscopy (OM), scanning electron microscopy (SEM) connected to an energy-dispersive spectrometer (EDS), x-ray diffraction (XRD), and positron annihilation Doppler broadening spectroscopy (PADBS) were used to examine the microstructure of alloys. Moreover, Vickers hardness and tensile tests were used to investigate the mechanical properties of the tested alloys. The G1 samples were cooled in the air to ~ 300 K and quenched G2 samples in cold water at 0 °C. The results showed that increasing the strain rate from 0.004 to 0.02 min −1 or decreasing the temperature from 503 to 423 K could increase the hardening parameters, yield stress ( σ y ), ultimate strength ( σ M ), and Young's modulus ( Y ) of all samples. Moreover, H V decreased as the aging temperature climbed from 423 to 503 K. Adding nano-sized CuO or cooling samples resulted in smaller grains. Furthermore, alloy B exhibited the formation of intermetallic compounds (IMCs) CuAl 2 and Cu 3 Si. The XRD data indicated the formation of phases in both alloys at 423, 463, and 503 K. In addition, the dislocation density, lattice strain, and average crystallite size were calculated. It can be seen from the activation energies and stress exponents that dislocation climbs through core diffusion as a control mechanism for both alloys. A significant positive relationship was observed between the value ( H v ) and PADBS parameters for all examined samples. The investigation showed that nano-sized CuO and a rapid cooling rate increased composite specimen hardness. This finding confirms that aluminum and its alloys play a crucial role in various technical applications.

The influence of the condensation rate on the structure of Cu-Mo pseudoalloys

Theoretical Investigation of Cu Influence on the Stability Characteristics of T-phase in Crossover Alloys

The thermal stability and degradation mechanism of Cu/Mo nanomultilayers

The influence of Zn$^{2+}$ ions on the local structure and thermochromic properties of Cu$_{1-x}$Zn$_x$MoO$_4$ solid solutions

Improving the mechanical properties and coefficient of thermal expansion of molybdenum-reinforced copper using powder metallurgy

Alloying Effects on the Microstructure and Mechanical Properties of Nanocrystalline Cu-based Alloyed Thin Films: Miscible Cu-Ti Vs Immiscible Cu-Mo

Unveiling the Mo effect on the microstructural stability of L1 2 -strengthened chemically complex alloys

Effect of Mo on microstructural stability of a 4th generation Ni-based single crystal superalloy

Effect of CuO Nanostructure Addition and Cooling Rate on the Microstructure and Mechanical Characteristics of Hypoeutectic Al-2wt.%Si Alloy

The Effect of Cooling Rate on the Microstructure and Mechanical Properties of Mg–Zn–Gd-based Alloys

Effects of cooling rates on precipitates in homogenized Al–Cu–Li alloy

Influence of Al and Mo on microstructure and tribological behaviors of Co-based superalloy

Study on the Solid Solubility Extension of Mo in Cu by Mechanical Alloying Cu with Amorphous Cr(Mo)

Effect of Mo Nanoparticles on Microstructure and Mechanical Properties of Cu Alloys by Self-Propagating and Spark Plasma Sintering

Influence of Zr addition on the microstructure, mechanical and electrical properties of Mo-Cu alloy

Nonequilibrium Alloy Formation In The Immiscible Cu-Mo System Studied By Thermodynamic Calculation And Ion Beam Mixing

The microstructures and mechanical properties of a highly alloyed Al-Zn-Mg-Cu alloy: The role of Cu concentration

Composition- and Temperature-Dependent Liquid Structures in Al–Cu Alloys: Anab Initiomolecular Dynamics and X-Ray Diffraction Study

Effect of Cu on the Spinodal Decomposition of AlZn Alloy with Symmetrical Composition

Effect of Molybdenum on Microstructures in Zr-1.2Nb Alloys after Β-Quenching and Subsequently 873 K Annealing

Microstructure and High Temperature Deformation Behavior of the Mo-ZrO 2 Alloys