Abstract:In order to achieve desired mechanical properties of alloys by manipulating grain boundaries (GBs) via solute decoration, it is of great significance to understand the underlying mechanisms of microstructural evolution and plastic deformation. In this work, nanocrystalline (NC) Cu-W alloyed films with W concentrations spanning from 0 to 40 at% were prepared by using magnetron sputtering. Thermal stability (within the temperature range of 200 °C-600 °C) and hardness of the films were investigated by using the x-ray diffraction, transmission electron microscope (TEM) and nanoindentation, respectively. The NC pure Cu film exhibited substantial grain growth upon all annealing temperatures. The Cu-W alloyed films, however, displayed distinct microstructural evolution that depended not only on the W concentration but also on the annealing temperature. At a low temperature of 200 °C, all the Cu-W alloyed films were highly stable, with unconspicuous change in grain sizes. At high temperatures of 400 °C and 600 °C, the microstructural evolution was greatly controlled by the W concentrations. The Cu-W films with low W concentration manifested abnormal grain growth (AGG), while the ones with high W concentrations showed phase separation. TEM observations unveiled that the AGG in the Cu-W alloyed thin films was rationalized by GB migration. Nanoindentation results showed that, although the hardness of both the as-deposited and annealed Cu-W alloyed thin films monotonically increased with W concentrations, a transition from annealing hardening to annealing softening was interestingly observed at the critical W addition of ∼25 at%. It was further revealed that an enhanced GB segregation associated with detwinning was responsible for the annealing hardening, while a reduced solid solution hardening for the annealing softening.

Alloying Effects on the Microstructure and Mechanical Properties of Nanocrystalline Cu-based Alloyed Thin Films: Miscible Cu-Ti Vs Immiscible Cu-Mo

Atomistic and Theoretical Insights on Nanoprecipitates-Controlled Strengthening Behavior for Optimum Mechanical Performance in Nanotwinned NiCoCr Alloys

Eff ects of Diff erent Mechanical Alloying Parameters on Microstructure of High Temperature Nanocrystalline Cu-Ta Alloys

Tuning the microstructure and mechanical properties of magnetron sputtered Cu-Cr thin films: The optimal Cr addition

The W alloying effect on thermal stability and hardening of nanostructured Cu-W alloyed thin films

An Insight into Mg Alloying Effects on Cu Thin Films:Microstructural Evolution and Mechanical Behavior

Tailoring microstructure and mechanical properties of Al-Mg-Si-Cu alloy with varying Mn and/or Cr additions

Alloying effects on the microstructure and mechanical properties of nanocrystalline Ti-based alloyed thin films

Combined effect of texture and nanotwins on mechanical properties of the nanostructured Cu and Cu–Al films prepared by magnetron sputtering

Designing Ultra-Strong Nanocrystalline Cu–Me (me = Mg, Al) Thin Films: Manipulation of Nanotwin Patterns

Theoretical Study of the Effects of Alloying Elements on Cu Nanotwins

Alloying Effects on the Microstructure and Properties of CoCrFeMnNiX0.1 High-Entropy Alloys Via Rolling and Thermal Treatment

Effect of Cu and Mn content on solidification microstructure, T-phase formation and mechanical property of Al Cu Mn alloys

Effect of Cu and Mn Content on Solidification Microstructure, T-phase Formation and Mechanical Property of AlCuMn Alloys

Effect of Mo Nanoparticles on Microstructure and Mechanical Properties of Cu Alloys by Self-Propagating and Spark Plasma Sintering

Influence of the Combined Additions Mn, Cr or Ni on the Formation of Dispersoids and Mechanical Properties of Al–Mg–Si–Cu Alloys

Effects of Mo and Cr Contents on Microstructures and Mechanical Properties of Near Β-Ti Alloy

Synergistic Effects of Chemical Composition on Precipitates, Dislocations, and Mechanical Properties of Precipitation-Strengthened Alloys

Mechanical Alloying of the Immiscible Cu-60wt%Cr Alloy: Phase Transitions, Microstructure, and Thermodynamic Characteristics

Twinning-governed plastic deformation in a thin film of body-centred cubic nanocrystalline ternary alloys at low temperature

Effects of Alloying on the Microstructures and Mechanical Property of Nb-Mo-Si Based in Situ Composites