Abstract:As the essential power control and adjustment component, microwave power attenuator has been widely applied in spectrum analyzer, network analyzer, receivers, and other microwave instrument systems. There has been significant interest in developing miniaturized microwave devices with small geometric dimension for commercial microwave test systems. Traditional attenuator with large size is difficult to integrate with IC due to its cumbersome mechanical relay or switches. Radio frequency microelectromechanical system (RF MEMS) switches present many advantages such as less insertion loss, higher isolation, better linearity, and lower power consumption and more importantly, its small size. It has absorbed great attention for the purpose of miniaturization of attenuator. Recent research shows step attenuator based on RF MEMS switches meet well the state-of-the-art requirements of miniaturized reconfigurable attenuation devices with high precision and broadband performance. In this chapter, we introduce a compact 3-bit step attenuator based on RF MEMS switches with 0 ~ 70 dB attenuation at 10 dB intervals up to 20GHz. The on-chip attenuator consists of 12 ohmic MEMS switches, 3 π-type resistive attenuation networks, and microwave compensate structures. To optimize the attenuation characteristics within the broadband, theoretical analysis and 3D modelling were performed. The device was obtained using MEMS process combined with polysilicon integrated circuit (IC) process.In section “Structure Design,” the structure of the step attenuator was proposed and three modules were designed independently including: (1) Resistive attenuation network. Two approaches are presented and discussed. (a) Polysilicon thin film resistor with symmetric topology is applied to realize the high-precision π-type resistive attenuation modules (10, 20, 40 dB). (b) Distributed TaN single thin film resistor (STFR) equivalent to π-type resistive network was designed with a more compact structure (2/3 compared to traditional network). It can realize 5 ~ 30 dB attenuation with less parasite effects. (2) RF MEMS switches. Toggling part is the determining factor to reduce the footprint of the entire attenuator. SP2T switch including 2 ohmic Au contact single-cantilever MEMS switches was customized for the attenuator. (3) CPW and microwave compensate structures. Precise design of the transmission path connecting each module is significant to suppress the inherent insertion loss and improve the matching performance. Right-angle bends and T-junctions were analyzed and designed. Based on the results of these three blocks, the overall attenuator was assembled and optimized with consideration of matching performance.In section “Fabrication,” we describe the fabrication method of RF MEMS attenuators. The 3-bit attenuator was manufactured with surface micromachining process and polysilicon IC techniques on 4 inch wafers and features 11 lithography steps. Key processes are emphasized including high-precision resistance and excellent ohmic contact between polysilicon and Au CPW was realized with experimental research. The photosensitive PI was used as sacrificial layer and the patterning process was simplified. The CPW and upper electrodes of the switch which were manufactured by low stress Au electroplating process have small roughness and without evident buckling after the sacrificial layer released. Based on these process studies, the 3-bit attenuator is successfully fabricated.In section “Characterization,” characterization of the obtained RF MEMS attenuator is presented. The measurement results show that the driven voltage of RF MEMS switch is 32 ~ 42 V and it can operate more than 3 × 108 times (cold switched mode). When toggling between the different transmission paths using MEMS switches, the 3-bit attenuator can realize target attenuation in range of 0 ~ 70 dB at 10 dB intervals up to 20 GHz. The accuracy and error of all the attenuation states is better than ±1.88 dB and 2.11 dB. The return loss of the 3-bit switched attenuator is better than 11.95 dB. Micromachined reconfigurable attenuator based on RF MEMS switch is demonstrated and can be further applied in particular microwave systems.

RF-MEMS Technology for 5G: Series and Shunt Attenuator Modules Demonstrated up to 110 GHz

RF-MEMS for 5G applications: a reconfigurable 8-bit power attenuator working up to 110 GHz. Part 2—Experimental characterisation of the RF behaviour

RF-MEMS for 5G applications: a reconfigurable 8-bit power attenuator working up to 110 GHz. Part 1: design concept, technology and working principles

RF-MEMS Technology for Future Mobile and High-Frequency Applications: Reconfigurable 8-Bit Power Attenuator Tested up to 110 GHz

RF-MEMS for future mobile applications: experimental verification of a reconfigurable 8-bit power attenuator up to 110 GHz

Discussion and Demonstration of RF-MEMS Attenuators Design Concepts and Modules for Advanced Beamforming in the Beyond-5G and 6G Scenario—Part 1

Discussion and Demonstration of RF-MEMS Attenuators Design Concepts and Modules for Advanced Beamforming in the Beyond-5G and 6G Scenario-Part 2

Design of a Low-Insertion-phase-shift MMIC Attenuator Integrated with a Serial-to-parallel Converter

An Ultra Broadband DC-40GHz 4-Bit GaAs Phemt MMIC Digital Attenuator

A Novel Ultra Broadband 8-45 GHz 4-Bit GaAs Pseudomorphic High Electron Mobility Transistors (phemt) Monolithic Digital Attenuator Used for Gain Control of Transceivers

A DC-32GHz 7-Bit Passive Attenuator with Capacitive Compensation Bandwidth Extension Technique in 55 Nm CMOS

A Compact 2-18Ghz Ultra-Wideband Frequency-conversion T/R Module Based on a 3D Heterogeneous Integrated Process

A Dc-20ghz Attenuator Design with Rf Mems Technologies and Distributed Attenuation Networks

Simple and fast modelling of radio frequency passives in view of beyond-5G and 6G applications: case study of an RF-MEMS multi-state network described by an equivalent lumped element network

A Miniaturized Reconfigurable Broadband Attenuator Based on RF MEMS Switches

A Micromachined Reconfigurable Attenuator

The Seven-State RF MEMS Miniaturized Broadband Reconfigurable Step Attenuator

An Ultra-Broadband Contact-Capacitive RF MEMS Switch for 15-110GHZ Applications

Design and investigation of a novel variable reactance-based capacitive RF-MEMS switch with multifrequency operation for mmWave applications

Design of Broadband High-Frequency Multi-Throw RF-MEMS Switches

An Advanced Real Time Lead RF-MEMS Based Switch Design for AI Applications