Abstract:Silicon heterojunction (SHJ) solar modules gained strong interest from solar photovoltaic (PV) module manufacturers and in the global market due to their high-efficiency potential. However, the presence of an amorphous silicon layer in SHJ structures raises concerns about their stability under light exposure. In this article, we compare the stability of SHJ modules to the stability of p-type and n-type homojunction monocrystalline silicon modules and of several thin-film PV technologies. The analysis is performed in intermediate precision conditions of measurement, where the same modules are measured indoors with the same measurement procedure, same location and equipment, and over an extended period of time, during which the modules are kept stored and not exposed to light. The results from all tested SHJ modules, which were also confirmed in reproducibility conditions, show a slow exponential degradation in the dark, which is fully recovered when the module is subsequently light-soaked. With this behavior, SHJ modules recall the metastability of certain thin-film technologies. The relevance of solar PV energy in the global electricity generation mix is at the present time unquestionable and all energy outlooks now report PV as a key player in the next decades for the transition toward a decarbonized energy system. When transferred into the manufacturing and deployment phase, the ambitious solar PV targets meet, among others, the challenge of accurate and reliable power rating of the PV modules, for which differences of a fraction of a percent mean significant investment gains or losses for the manufacturers, investors, and final users. The factors that mainly affect the uncertainty of PV power rating in the production line are the accuracy in the calibration of the reference modules and their temporal stability. Among other PV technologies, SHJ, with an efficiency that now goes beyond 22% at the module level and is expected to increase further, is the fastest gaining in market share (estimated to hit 10% by 2024 and 20% by 2032). However, the observed "metastability" (i.e., the change of the electrical performance to a status with lower or higher stable power when the module is stored in the dark for a prolonged period of time), which is discussed in this article for commercial SHJ modules, although not affecting the field performance, may impact the production capacity and should be carefully addressed by SHJ module manufacturers, researchers, and testing laboratories.

Shunts in crystalline silicon PV modules: A comprehensive review of investigation, characterization, and mitigation

Hotspots and Performance Evaluation of Crystalline-Silicon and Thin-Film Photovoltaic Modules

Performance Benchmark of Bypassing Techniques for Photovoltaic Modules

Application of Electroluminescence Imaging to Distinguish Ohmic and Non Ohmic Shunting in Inaccessible Cells Within a PV Module

Effect of partial shading on photovoltaic systems performance and its mitigation techniques-a review

Impact of partial shading on the performance and reliability of potential-induced degraded crystalline silicon PV module

Review of Mismatch Mitigation Techniques for PV Modules

Is Shunt Quenching Relevant to Minimize Shunt Losses in Perovskite–Silicon Tandem Solar Cells?

Predicting unparalleled degradation progression in PV module using simulation of shunt resistance experimental data

On the metastability of silicon heterojunction solar photovoltaic modules

Safety Analysis of Solar Module under Partial Shading

Modelling and experimental investigations of microcracks in crystalline silicon photovoltaics: A review

Optimization of Shunt Isolation Processing for Silicon Solar Cells Via Laser and Chemical Etching

Performance analysis of partially shaded high-efficiency mono PERC/mono crystalline PV module under indoor and environmental conditions

Elimination of Severe Shunting Problems Due to Air-Side Electrode Formation on Evaporated Poly-Si Thin-Film Solar Cells on Glass

A Simple Mismatch Mitigating Partial Power Processing Converter for Solar PV Modules

Analysis of leakage current in GaAs micro-solar cell arrays

Challenges and advantages of cut solar cells for shingling and half-cell modules

Research on temperature anomalies caused by the shading of individual solar cells in photovoltaic modules

Spatially Resolved Identification of Shunt Defects in Thin Film Solar Cells via Current Transport Efficiency Imaging Combined with 3D Finite Element Modeling

A Review on Investigation of PV Solar Panel Surface Defects and MPPT Techniques