Abstract:Micro-arc oxidation (MAO) has been an important surface treatment of Al alloys for surface hard-coating and corrosion protection. We used direct current (DC) as the power supply at a constant current density 10 A/dm(2) during 30-min MAO processing of 6061 Al alloy. The electrolyte bath contained 9.765 g/L Na2SiO3 added with 10-60 mL/L ammonia water. With increasing added ammonia water in electrolyte bath, anomalous layer-thickening was observed reproducibly. Average coating thickness increases three times from 44 mm (no addition) to 135 mm (60 mL/L added). At 30 mL/L ammonia water micro-hardness of MAO layer maximizes at 1070 HV. X-ray diffraction shows the increasing intensity of amorphous phase accompanying with layer thickening. SEM analyses depict that size of surface micro-pore reduces with increasing added amount of ammonia water. Cross-sectional micrographs reveal micro-pores with a continuous coating-substrate interface. Elemental mapping and line-scans indicate uniform distribution of Al, O, Si and Na through the thickness of coating. Corrosion current density is plausibly improved to 6.41 x 10(10) A/cm(2) by the addition of 60 mL/L ammonia water, whereas layer hardness is 840 HV. Anomalous thickening effect was not observed in case of surface layers micro-arc treated in ammonia water added electrolyte of sodium aluminate. In the later case no amorphous phase is observed in the MAO coating. The mechanism of anomalous thickening arises from the formation of amorphous surface-layer which entrapped large amount of solid debris formed during the discharging process and dispersing in electrolyte. The most significance of this highly corrosion-resistant thick and hard layer lies in the 66.7% energy budget when only 1/3 thickness is required. (C) 2016 Elsevier B.V. All rights reserved.

An effective micro-arc oxidation (MAO) treatment on aluminum alloy for stronger bonding joint with carbon fiber composites

Micro-arc Oxidation Behaviors of AZ91D Magnesium Alloy in Different Electrolytes

Reinforcement study of anodizing treatment with various temperatures on aluminum substrates for stronger adhesive bonding with carbon fiber composites

Surface pre-oxidation for enhancing laser assisted joining between carbon fiber reinforced thermoplastic composites and AZ31B Mg alloy

Micro-arc oxidation of Al alloys: mechanism, microstructure, surface properties, and fatigue damage behavior

Micro/nano dual-scale porous surface structure of the Al alloys and improvement on the joint strength with carbon fiber reinforced PA 6 thermoplastic

Effect of Several Inorganic Additives on Microstructure and Properties of Microarc Oxidation Coating on Aluminium Alloy

Surface Treatments for Enhancing the Bonding Strength of Aluminum Alloy Joints

Microstructure, MAO Performance, Interfacial Characteristics and Corrosion Behavior of FSW Joint of Al-Mg-Sc Alloy

Evaluation of the micro-arc oxidation treatment effect on the protective performance of a Mg-rich epoxy coating on AZ91D magnesium alloy

Improved wear and corrosion resistance of alumina alloy by MAO and PECVD

Effect of Α-Al2o3 Additive on the Microstructure and Properties of MAO Coatings Prepared on Low Carbon Steel

A new strategy for developing interfacial bonding using non-metallic atoms in carbon nanotube-reinforced aluminum composites

Growth Mechanism and Performance of MAO-AO Composite Coating Obtained by Two-Stage Process.

Microstructure and corrosion behavior of micro-arc oxidation coating on 6061 aluminum alloy pre-treated by high-temperature oxidation

Adhesion and Corrosion Resistance of Micro-Arc Oxidation/Polyurethane Composite Coating on Aluminum Alloy Surface

Anomalous Layer-Thickening During Micro-Arc Oxidation of 6061 Al Alloy

Processing and Analysis of Micro-Arc Oxidation Coating on 319S Aluminum Alloy

Microarc Oxidation Coating Combined with Surface Pore-Sealing Treatment Enhances Corrosion Fatigue Performance of 7075-T7351 Al Alloy in Different Media

Corrosion and tribocorrosion resistance of MAO-based composite coating on AZ31 magnesium alloy

Forming Epoxy Coatings on Laser-Engraved Surface of Aluminum Alloy to Reinforce the Bonding Joint with a Carbon Fiber Composite