Abstract:Balancing interfacial stability and Li+ transfer kinetics through surface engineering is a key challenge in developing high-performance battery materials. Although conformal coating enabled by atomic layer deposition (ALD) has shown great promise in controlling impedance increase upon cycling by minimizing side reactions at the electrode–electrolyte interface, the coating layer itself usually exhibits poor Li+ conductivity and impedes surface charge transfer. In this work, we have shown that by carefully controlling postannealing temperature of an ultrathin ZrO2 film prepared by ALD, Zr4+ surface doping could be achieved for Ni-rich layered oxides to accelerate the charge transfer yet provide sufficient protection. Using single-crystal LiNi0.6Mn0.2Co0.2O2 as a model material, we have shown that surface Zr4+ doping combined with ZrO2 coating can enhance both the cycle performance and rate capability during high-voltage operation. Surface doping via controllable postannealing of ALD surface coating layer reveals an attractive path toward developing stable and Li+-conductive interfaces for single-crystal battery materials.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acs.nanolett.0c03778?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acs.nanolett.0c03778</a>.Quasi in situ X-ray photoelectron spectroscopy (XPS) characterizations of Zr 3d and Ni 2p (Figure S1), XPS characterizations of O 1s (Figure S2), energy-dispersive spectroscopy (EDS) mapping of 50-ZrO2-700 °C-NCM (Figure S3), cross-sectional scanning electron microscopy (SEM) images of SC-NCM and 5-ZrO2-NCM electrode collected after 50 cycles (Figure S4), reproducible cycle and rate performance of 5-ZrO2-500 °C-NCM (Figure S5), XPS characterizations of F 1s (Figure S6), SEM characterizations of SC-NCM; 5-ZrO2-NCM; 5-ZrO2-500 °C-NCM; 5-ZrO2-700 °C-NCM after 50 cycles (Figure S7), cycle stability of NCM cathodes at 1 C (180 mA/g) in this study compared to literature reports (Table S1) (<a class="ext-link" href="/doi/suppl/10.1021/acs.nanolett.0c03778/suppl_file/nl0c03778_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

Enhancing the interfacial stability of LiNi 0.8 Co 0.15 Al 0.05 O 2 cathode materials by a surface-concentration gradient strategy

Enhancing high-voltage performances of nickel-based cathode material via aluminum and progressive concentration gradient modification

Enhanced Electrochemical Performance of LiNi0.8Co0.15Al0.05O2 Cathode Material via Li2TiO3 Nanoparticles Coating

Progressive Concentration Gradient Nickel-Rich Oxide Cathode Material for High-Energy and Long-Life Lithium-Ion Batteries

Simultaneous Enhancement of Interfacial Stability and Kinetics of Single-Crystal LiNi0.6Mn0.2Co0.2O2 Through Optimized Surface Coating and Doping

Role Of Fluorine Surface Modification In Improving Electrochemical Cyclability Of Concentration Gradient Li[Ni0.73co0.12mn0.15]O-2 Cathode Material For Li-Ion Batteries

Simultaneous Enhancement of Interfacial Stability and Kinetics of Single-Crystal LiNi 0.6 Mn 0.2 Co 0.2 O 2 through Optimized Surface Coating and Doping

Development of Diverse Aluminium Concentration Gradient Profiles in Ni-Rich Layered Cathodes for Enhanced Electrochemical and Thermal Performances

Surface enrichment and diffusion enabling gradient-doping and coating of Ni-rich cathode toward Li-ion batteries

Enhanced Interfacial Kinetics and High Rate Performance of LiCoO2 Thin-Film Electrodes by Al Doping and in Situ Al2O3 Coating.

Tuning Li/Ni mixing by reactive coating to boost the stability of cobalt-free Ni-rich cathode

Stabilizing Cathode Materials of Lithium-Ion Batteries by Controlling Interstitial Sites on the Surface

Enhancing Interfacial Stability in Sulfide All-Solid-state Batteries Through Surface Dual-Doping of Zr and F in Ni-rich Cathodes

LiNbO3 Coating and F- Doping Stabilize the Crystal Structure and Ameliorate the Interface of LiNi0.88Co0.06Mn0.03Al0.03O2 to Improve the Electrochemical Properties and Safety Capability

Stabilizing high-Ni cathodes with gradient surface Ti-enrichment

Enabling Enhanced Cycling Stability of a LiNi0.8Co0.15Al0.05O2 Cathode by Constructing a Ti-Rich Surface

The surface double-coupling on single-crystal LiNi0.8Co0.1Mn0.1O2 for inhibiting the formation of intragranular cracks and oxygen vacancies

Enhanced interfacial reaction interface stability of Ni-rich cathode materials by fabricating dual-modified layer coating for lithium-ion batteries

Effectively stabilizing electrode/electrolyte interface of high-energy LiNi0.9Co0.1O2//Si–C system by simple cathode surface-coating

A novel perspective on surface modification of LiNi0.5Co0.2Mn0.3O2 cathode materialfor lithium‐ion batteries

Stabilizing the surface of LiNi0.815Co0.15Al0.035O2 by a facile pre-oxidation-coating strategy on the precursor