Abstract:The effects of temperature on the tribological and dynamic mechanical properties (DMP) of aromatic liquid-crystal poly(ester-co-amide) were investigated. Specimens for the DMA test and friction and wear test were prepared by compression molding at elevated temperature. The dynamic mechanical properties of the resulting compression-molded liquid crystal polymer (LCP) specimens were evaluated on a Perkin-Elmer DMA instrument, in a three-point bending mode, at a heating rate of 10°C/min and frequency of 1Hz from room temperature to 250°C. The friction and wear behavior of the compression-molded LCP specimens sliding against SA52100 steel in a ball-on-disk configuration was evaluated on a high-temperature friction and wear tester from 25 to 300°C. The worn surface morphologies of the compression-molded LCP specimens were observed on a scanning electron microscope. It was found that the tribological and dynamic mechanical properties of the LCP strongly depended on the test temperature. Namely, the friction coefficients decreased significantly and the wear rate increased considerably with increasing temperature. This was attributed to the enhanced softening and plastic deformation of the LCP at elevated temperature. The LCP experienced severe plastic deformation, flowing and local melting owing to the destruction of the stiff backbones of the polymeric molecules at excessively high temperature, thus the largest wear rate of the tested LCP was generated at 300°C. Such a trend in the friction and wear behavior of the compression-molded LCP with temperature conformed well to the corresponding worn surface morphologies. Namely, the LCP worn surface was characterized by mild plastic deformation and micro-cracking as the LCP disk slid against the steel ball at 50°C, whilst at 100°C, the plastic deformation and adhesion became severe and the micro-cracking disappeared owing to the plastic flow. The plastic deformation and adhesion became increasingly more severe with further increase of the test temperature up to 150, 200, and 250°C, owing to the increased plastic flow and local softening and melting of the LCP. Moreover, the storage modulus of the compression-molded LCP greatly decreased with increasing temperature, as did the loss modulus, while the complex modulus and tan δ increased with increasing temperature, which agreed well with the corresponding trend of the tribological behavior with temperature. It was confirmed that the dynamic mechanical properties of the polymer were an important factor of the high temperature tribological behavior.

A note on intrinsic viscosity–temperature relationships

Effects of Temperature on Elastic Behavior of Short Compact Polymers

Effect of Temperature on the Tribological and Dynamic Mechanical Properties of Liquid Crystalline Polymer

A Monte Carlo Study Of The Glass Transition Of Polymethylene

A note on intrinsic viscosity–molecular weight relationships

Molecular weight dependence of the intrinsic viscosity of polymer solutions. II

Intrinsic viscosity–molecular weight relationship for polychlorotrifluoroethylene

Relation between molecular weight and intrinsic viscosity for polymethyl methacrylate

Temperature Memory Effect and Its Stability Revealed Via Differential Scanning Calorimetry in Ethylene‐vinyl Acetate Within Glass Transition Range

The effect of temperature, conversion and solvent on the stereospecificity of the free radical polymerization of methyl methacrylate

New Insight Into Time-Temperature Correlation For Polymer Relaxations Ranging From Secondary Relaxation To Terminal Flow: Application Of A Universal And Developed Wlf Equation

The Intermediate Temperature T* Revealed In Relaxor Polymers

Conformation of A Polyfluorene Derivative in Solution

The temperature dependence of the Hildebrand solubility parameters of selected hydrocarbon polymers and hydrocarbon solvents: a molecular dynamics investigation

Temperature Dependence of Chain Conformation and Local Rigidity of Isomerized Polyimides in Dimethyl Formamide

Viscosity Behavior of Solution Copolymerization of Acrylonitrile and Itaconic Acid: On-Line Determination and Theoretical Analysis

Temperature-Structure Dependence Of Poly(1-Octene-Co-T-Butyl Acrylate) Prepared By Conventional Free Radical Polymerization

Chain flexibility and glass transition temperatures of poly(n-alkyl (meth)acrylate)s: Implications of tacticity and chain dynamics

Turbidity of Critical Solutions of Polymethylmethacrylate in 3-Octanone

Application of Time-Temperature Superposition Principle to Polymer Transition Kinetics

Temperature and Solvent Viscosity Tune the Intermediates During the Collapse of a Polymer