Abstract:The present work aims to examine the reciprocating wear characteristics at elevated temperatures (200 °C, 400 °C, and 600 °C) of CoCrFeNiW 0.3 + 5 at% C high entropy alloy coatings, which has been synthesized by atmospheric plasma spraying. The experimental findings pertaining to the worn surface demonstrate that an increase in testing temperature leads to a reduction in wear scar depth. The findings derived from the examination using field emission scanning electron microscopy (FESEM) revealed the existence of wear debris, an adhesive layer, craters, and scratches on the surfaces that were subjected to wear. The examination of worn surfaces using X-ray photoelectron spectroscopy (XPS) has shown the existence of several oxides. The presence of oxides is established while evaluating worn surfaces by Fourier transform infrared spectroscopy (FTIR). The X-ray diffraction (XRD) analysis reveals that the lack of oxide development might perhaps be attributed to the limited width of the worn track. The observed reduction in wear volume loss with increasing testing temperature may be attributable to the reaction arise inside the tribolayer and oxides formation. The energy-dispersive X-ray spectroscopy (EDS) examination of the Al 2 O 3 counter body indicated the presence of a transferred tribofilm. The alloy coating, namely the CoCrFeNiW 0.3 + 5 at% C alloy coating, exhibits a decreased mass loss of 9.43 mg and an average coefficient of friction of 0.46 at a test temperature of 600 °C. When the sample is subjected to a wear testing temperature of 600 °C, the wear mass is decreased by 24.37%. The results of this investigation provide promising prospects for practical use in applications requiring high temperature wear resistance.

Investigation of Wear Behavior of 34CrNiMo6 Low Alloy Steel Coated by PACVD Method

Investigation of Wear, Surface, Metallurgical and Mechanical Properties of Ti6Al4V Alloys Coated with PVD Method

Wear behavior of Cr3C2-NiCr detonation spray coating

Modification of flame-sprayed NiCrBSi alloy wear-resistant coating by friction stir processing and furnace re-melting treatments

Enhancing mechanical and tribological performance of CrN/CrTiSiN coating through annealing treatment

Influence of Molybdenum on the Microstructure and Wear Resistance of Nickel-Based Alloy Coating Obtained by Plasma Transferred Arc Process

Influence of N2 Flow Rate on the Microstructure, Mechanical, and Tribological Properties of Ti-Al-Cr-N Coating: Dry Milling Investigation on 6061 Aluminum Alloy

Microstructure Evolution and Enhanced Wear Resistance of Al2CrFeNiMo High Entropy Alloy Coating Fabricated by Laser Cladding

Cavitation Erosion and Sliding Wear of MCrAlY and NiCrMo Coatings Deposited by HVOF Thermal Spraying

Wear resistance of a Cr 3 C 2 -NiCr detonation spray coating

Structure and Wear Behavior of AlCrSiN-based Coatings

Microstructure and Wear Resistance of High Volume Fraction Carbide (cr, Fe)7C3 Reinforced Fe Based Coating

Characterization and Wear Behavior of CoCrNi Medium Entropy Alloy Coating on Al Alloy by Resistance Seam Processing

High temperature tribological behavior of atmospheric plasma-sprayed CoCrFeNiW0.3 + 5 at% C high-entropy alloy coating

Mechanical, Tribological, and Electrochemical Evaluation of NiCrAlMoFe Thermally Sprayed Coatings Subject to Post-treatments

Microstructure evolution and mechanical performance of Cr-N/Al-Cr multilayer coatings produced by plasma nitriding Cr-coated Al alloy

High Temperature Oxidation and Tribological Behavior of Cr3C2-25CoNiCrAlY and Cr3C2-25NiCr Coatings Prepared by AC-HVAF

EFFECT OF CrMoN HARD COATINGS WITH DIFFERENT COM-POSITIONS ON THE SURFACE PROPERTIES OF DIE STEELS

Microstructure and Corrosive Wear Properties of CoCrFeNiMn High-Entropy Alloy Coatings

Influence of Cr on the Surface Properties of the Micro-Textured WC+Co Alloy Coating

Microstructure, Adhesion and Tribological Properties of CrN/CrTiAlSiN/WCrTiAlN Multilayer Coatings Deposited on Nitrocarburized AISI 4140 Steel