Abstract:Semitransparent front electrodes for polymer solar cells, that are printable and roll-to-roll processable under ambient conditions using different approaches, are explored in this report. The excellent smoothness of indium-tin-oxide (ITO) electrodes has traditionally been believed to be difficult to achieve using printed front grids, as surface topographies accumulate when processing subsequent layers, leading to shunts between the top and bottom printed metallic electrodes. Here we demonstrate how aqueous nanoparticle based silver inks can be employed as printed front electrodes using several different roll-to-roll techniques. We thus compare hexagonal silver grids prepared using either roll-to-roll inkjet or roll-to-roll flexographic printing. Both inkjet and flexo grids present a raised topography and were found to perform differently due to only the conductivity of the obtained silver grid. The raised topographies were compared with a roll-to-roll thermally imprinted grid that was filled with silver in a roll-to-roll process, thus presenting an embedded topography. The embedded grid and the flexo grid were found to perform equally well, with the flexographic technique currently presenting the fastest processing and the lowest silver use, whereas the embedded grid presents the maximally achievable optical transparency and conductivity. Polymer solar cells were prepared in the same step, using roll-to-roll slot-die coating of zinc oxide as the electron transport layer, poly-3-hexylthiophene:phenyl-C(61)-butyric acid methyl ester (P3HT:PCBM) as the active layer and poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) as the top electrode, along with a flat bed screen printed silver grid. The power conversion efficiency (PCE) obtained for large area devices (6 cm(2)) was 1.84%, 0.79% and 1.72%, respectively, for thermally imprinted, inkjet and flexographic silver grids, tested outside under the real sun. Central to all three approaches was that they employed environmentally friendly solvents, i.e. water based nanoparticle silver inks.

Polymer solar cell modules prepared using roll-to-roll methods: Knife-over-edge coating, slot-die coating and screen printing

All Polymer Photovoltaics: from Small Inverted Devices to Large Roll-to-roll Coated and Printed Solar Cells

Grid-connected polymer solar panels: initial considerations of cost, lifetime, and practicality

Roll-to-Roll Slot-Die-Printed Polymer Solar Cells by Self-Assembly.

Highly Flexible All‐Polymer Solar Cells Processed Without Post‐Treatment Achieving 13.56% Efficiency

Flexible OPV modules for highly efficient indoor applications

Silver front electrode grids for ITO-free all printed polymer solar cells with embedded and raised topographies, prepared by thermal imprint, flexographic and inkjet roll-to-roll processes

Roll‐to‐Roll Printed Large‐Area All‐Polymer Solar Cells with 5% Efficiency Based on a Low Crystallinity Conjugated Polymer Blend

Matrix Organization and Merit Factor Evaluation as a Method to Address the Challenge of Finding a Polymer Material for Roll Coated Polymer Solar Cells

Aggregation‐Induced Multilength Scaled Morphology Enabling 11.76% Efficiency in All‐Polymer Solar Cells Using Printing Fabrication

Slot-die processing and encapsulation of non-fullerene based ITO-free organic solar cells and modules

Fully Printed and Industrially Scalable Semitransparent OPV Modules: Navigating through Material and Processing Constraints

Flexible Polymer-Organic Solar Cells Based on P3HT:PCBM Bulk Heterojunction Active Layer Constructed under Environmental Conditions

Fully Roll-to-Roll Processed Efficient Perovskite Solar Cells via Precise Control on the Morphology of PbI2:CsI Layer

A Top‐Down Strategy to Engineer ActiveLayer Morphology for Highly Efficient and Stable All‐Polymer Solar Cells

Slot-die coated large-area flexible all-polymer solar cells by non-halogenated solvent

Toward Solution-Processed High-Performance Polymer Solar Cells: from Material Design to Device Engineering

Slot-die coating of a formamidinium-cesium mixed-cation perovskite for roll-to-roll fabrication of perovskite solar cells under ambient laboratory conditions

Roll-coating Fabrication of Flexible Large Area Small Molecule Solar Cells with Power Conversion Efficiency Exceeding 1%

Simplifying contact-layer design for high-throughput printing of flexible perovskite photovoltaics

In Situ Structure Characterization in Slot‐Die‐Printed All‐Polymer Solar Cells with Efficiency over 9%