Abstract:Despite the rapid progress that has been made in increasing the power conversion efficiency (PCE) of organic solar cells (OSCs) over the past decade, it is a challenge to realize efficient and environment-friendly OSCs. In this contribution, all polymer solar cells were fabricated with a blend of poly[4,8-bis(5-(2-ethylhexyl) thiophen-2-yl) benzo[1,2-b: 4,5-b'] dithiophene-co-3-fluorothieno[3,4-b] thiophene-2-carboxylate] (PTB7Th) donor and vinylene-bridged perylenediimide-based polymer (PDI-V) acceptor, in which non-halogenated tetrahydrofuran (THF) was used as the host solvent. A conventional device structure of ITO/poly(3,4-ethylenedioxythiophene): poly(styrenesulfonate) (PEDOT:PSS)/PTB7-Th:PDI-V/zirconium acetylacetonate (ZrAcac)/Al was employed, where PEDOT:PSS functioned as the hole transporting layer (HTL) and ZrAcac functioned as the electron transporting layer (ETL). The mixed solution of PTB7-Th and PDI-V was spin cast on the top of PEDOT:PSS layer to form the active layer. After that, ZrAcac solution was spin cast on the top of PTB7-Th:PDI-V layer. Different thermal annealing temperatures were used to optimize the active layer morphology. In details, OSCs without thermal annealing showed a PCE of 7.1%, with a short-circuit current (J(SC)) of 14.9 mA/cm(2), an open-circuit voltage (V-OC) of 0.74 V, and a fill factor (FF) of 64%. The devices annealed at 120 degrees C showed a high PCE of 8.1% with a J(SC) of 15.5 mA/cm(2), a V-OC of 0.74 V, and a FF of 70%. Further increasing the annealing temperature to 150 degrees C led to decreased FF and thereby a relatively lower PCE (7.4%). To the best of our knowledge, the PCE of similar to 8.1% is one of the highest PCE values reported in the literature so far for all polymer solar cells. The high and balanced hole and electron mobility partially contributed to such a high performance. These results suggest that THF as good non-halogenated solvent can be used to fabricate high-performance all polymer solar cells. Higher efficiency can be achieved for OSCs with THF solvent when better polymer acceptors are employed.

Slot-die coated large-area flexible all-polymer solar cells by non-halogenated solvent

Highly Flexible All‐Polymer Solar Cells Processed Without Post‐Treatment Achieving 13.56% Efficiency

A Sequential Slot‐Die Coated Ternary System Enables Efficient Flexible Organic Solar Cells

Efficient Large Area All‐Small‐Molecule Organic Solar Cells Fabricated by Slot‐Die Coating with Nonhalogen Solvent

Processing-Friendly Slot-Die-Cast Nonfullerene Organic Solar Cells with Optimized Morphology.

Enabling Roll-Processed and Flexible Organic Solar Cells Based On PffBT4T Through Temperature-Controlled Slot-Die Coating

Printable and Stable All-Polymer Solar Cells Based on Non-Conjugated Polymer Acceptors with Excellent Mechanical Robustness

High-efficiency Flexible Organic Solar Cells with a Polymer-Incorporated Pseudo-Planar Heterojunction.

Regulation of Polymer Configurations Enables Green Solvent-Processed Large-Area Binary All-Polymer Solar Cells With Breakthrough Performance and High Efficiency Stretchability Factor

Hot Hydrocarbon‐Solvent Slot‐Die Coating Enables High‐Efficiency Organic Solar Cells with Temperature‐Dependent Aggregation Behavior

Roll‐to‐Roll Printed Large‐Area All‐Polymer Solar Cells with 5% Efficiency Based on a Low Crystallinity Conjugated Polymer Blend

Regulating Phase Separation Kinetics for High‐efficiency and Mechanically Robust All‐Polymer Solar Cells

Synergistic Optimization Enables Large‐Area Flexible Organic Solar Cells to Maintain over 98% PCE of the Small‐Area Rigid Devices

Non-conjugated terpolymer acceptors for highly efficient and stable lager-area all-polymer solar cells

The Conjugated/Non‐Conjugated Linked Dimer Acceptors Enable Efficient and Stable Flexible Organic Solar Cells

Highly Efficient Flexible Roll-to-Roll Organic Photovoltaics Based on Non-Fullerene Acceptors

Environmentally Friendly and Roll-Processed Flexible Organic Solar Cells Based on PM6:Y6

High-performance All Polymer Solar Cells Fabricated with Non-halogenated Solvent

Large-area,Flexible Polymer Solar Cell Based on Silver Nanowires As Transparent Electrode by Roll-to-Roll Printing

Nonhalogenated‐Solvent‐Processed High‐Performance All‐Polymer Solar Cell with Efficiency over 14%

All Polymer Photovoltaics: from Small Inverted Devices to Large Roll-to-roll Coated and Printed Solar Cells