Abstract:Air travel has become one of the most common means of transportation. The most common question which is generally asked is: How does an airplane gain lift? And the most common answer is via the Bernoulli principle. It turns out that it is wrongly applied in common explanations, and there are certain misconceptions. In an alternative explanation the push of air from below the wing is argued to be the lift generating force via Newton's law. There are problems with this explanation too. In this paper we try to clear these misconceptions, and the correct explanation, using the Lancaster-Prandtl circulation theory, is discussed. We argue that even the Lancaster-Prandtl theory at the zero angle of attack needs further insights. To this end, we put forward a theory which is applicable at zero angle of attack. A new length scale perpendicular to the lower surface of the wing is introduced and it turns out that the ratio of this length scale to the cord length of a wing is roughly $0.4930\pm0.09498$ for typical NACA airfoils that we analyzed. This invariance points to something fundamental. The idea of our theory is simple. The "squeezing" effect of the flow above the wing due to camber leads to an effective Venturi tube formation and leads to higher velocity over the upper surface of the wing and thereby reducing pressure according the Bernoulli theorem and generating lift. Thus at zero angle of attack there is no need to invoke vortex and anti-vortex pair generation. In fact vortex and anti-vortex pair generation cannot be justified. We come up with the equation for the lift coefficient at zero angle of attack: \[C_l = \frac{1}{c}\int_0^c dx \left(\frac{h_c^2}{(h_c - f(x))^2}-1\right).\] Here $C_l$ is the lift coefficient, $h_c$ is our new length scale perpendicular to the lower surface of the wing and $f(x)$ is the functional profile of the upper surface of the wing.

Penerapan Teori Klasik Airfoil Tipis Ber-camber pada Profil NACA 64-206

Experimental and Numerical Studies on Aerodynamic Control of NACA 4418 Airfoil with a Rotating Cylinder

Effects of Cambers of Corrugated Airfoils on Gliding Performance by Using Lattice Boltzmann Method

Airfoil Parameterization Evaluation Based on a Modified PARASEC Method for a H-Darrious Rotor

THE EFFECTS OF ANGLE OF ATTACK, REYNOLD NUMBERS AND WINGLET STRUCTURE ON THE PERFORMANCE OF CESSNA 172 SKYHAWK

Computational and experimental study on the aerodynamic performance of NACA 4412 airfoil with slot and groove

NACA 0012 VE NACA 4412 Kanat Kesitlerinin Yeniden Tasarlanarak Had ile Analiz Edilmesi

Optimizing NACA Airfoil Thickness Function Parameters for Maximum Lift-to-Drag Ratio

Effect of Ground Proximity on Aerodynamic Characteristics of NACA 4412 Airfoil.

Optimization Design of Airfoil Propellers of Modified NACA 4415 Using Computational Fluids Dynamics

Effect of thickness, camber, and thickness distribution on airfoil characteristics at Mach numbers up to 1.0

Low-speed characteristics of four cambered, 10-percent-thick NACA airfoil sections

Optimizing Winglet Cant Angle for Enhanced Aircraft Wing Performance Using CFD Simulation and Hybrid ANN‐GA

Experimental Study on the Effect of Boundary Layer Control on the Aerodynamics Characteristics of NACA 0021 Aerofoil

Airfoil Lift Calculation Using Wind Tunnel Wall Pressures

Design and aerodynamics analysis of rear wing formula student car using 3 dimension CFD (computational fluid dynamics)

Improvement of NACA6309 Airfoil with Passive Air-Flow Control by using Trailing Edge Flap

Nonlinear geometric decomposition of airfoils into the thickness and camber contributions

Direct numerical simulation of cambered airfoil aerodynamics at Re = 20,000

Clearing certain misconception in the common explanations of the aerodynamic lift

Aerodynamic Study of Leading-Edge Protuberance to Improve the Performance of NACA 0009 Blade