Abstract:Butt joints of the V-1461 and 1424 heat treated aluminum–lithium alloys of the third generation were welded with a CO 2 laser and studied in detail for the first time. In particular, spatial distributions of the formed phases and their evolution upon post-weld heat treatment (PWHT), determining the mechanical properties of the joints, were investigated. The PWHT included quenching and subsequent artificial aging. The key factors, affecting the metallurgical processes in a weld pool, were the following: 1) the alloying elements and the thermal properties of the alloys, 2) the dynamics of the local non-equilibrium melting, the convective transfer of the molten metal in the weld pool and its subsequent solidification, 3) the cooling rate, and 4) the PWHT procedure. By using synchrotron radiation and scanning electron microscopy, new θ(Al 2 Cu), T 1 (Al 2 CuLi) and S 1 (Al 2 MgLi) phases were found in the weld metal that were absent in both base metals. This phenomenon reduced the mechanical properties of the joints to the levels, corresponding to about 50 % of the 1424 alloy as the weakest one. Quenching contributed to the formation of the δ′(Al 3 Li) strengthening phase in the weld metal. As a result, the ultimate tensile strength increased up to 70 % and elongation up to 95 % of the corresponding levels of the 1424 alloy. Artificial aging made it possible to form the T1(Al 2 CuLi) strengthening phase, to increase the content of the δ′(Al 3 Li) one, as well as to improve the mechanical properties of the joint. In this case, the ultimate tensile strength was 411 MPa, the yield point was 327 MPa and elongation was 1.7 %. These values were close to those for the 1424 alloy (about 80 %, 89 % and 23 %, respectively).

New insight into laser butt welded nonporous SiCp/2A14Al joint: Interfaces, precipitation phase and mechanical properties

Characterization of Si–Cu–C–Al quaternary interface of SiC/2A14 joint via counterintuitive laser butt welding

Microstructure Evolution and Mechanical Properties of 20%SiCp/Al Joint Prepared via Laser Welding

Laser Beam Oscillation Welded SiCp/2xx Al Alloy: Microstructure, Phase Interface and Mechanical Properties

In-situ formation Ti-Al-C compounds reinforced SiCp/2A14 Al joint: Microstructure evolution and mechanical properties

Influence of Si content on interfacial reactions and mechanical properties of dual-spot laser welded-brazed Ti/Al joints

Effect of Silicon Content in Al–Si Welding Wire on Mechanical Properties of Al/Cu Laser Welded Joint

Effects of laser power on the microstructural evolution and mechanical performance in laser dissimilar welding of TC4 to SiCp/6092Al composite

Laser welding of SiCp/2024Al composites with novel TiB2/2024Al composite filler

Microstructure and mechanical properties of SiC reinforced AlSi10Mg composites fabricated by laser metal deposition

New insight into microstructure and mechanical properties of heterostructures 7075 Al joint prepared via single mode laser welding

Toward understanding the fractured mechanism in laser welded–brazed Al/steel interface by in–situ SEM tensile observations

Effects of Si contents in filling wires on microstructure evolution and properties of Al-steel dissimilar joint by laser welding-brazing

Solidification microstructures and softening behavior of laser welded 6082-A356 aluminum alloy dissimilar butt joints

Influence of micron and nano SiCp on microstructure evolution and mechanical properties of laser metal deposition AlSi10Mg alloy

Dissimilar joining of TC4 and SiC p /6092Al matrix composite by laser lap welding technology

The characteristics and dynamics of fused silica-aluminum alloy welding during mJ-level femtosecond laser

Laser processing of Mg-10Li-3Al-3Zn alloy: Part I – Microstructure and properties of laser welded joints

Effect of post-weld heat treatment on the microstructure, phase composition and mechanical properties of dissimilar Al-Mg-Li/Al-Cu-Li laser welded joints

Laser pressure welding of dissimilar aluminium and copper: microstructure and mechanical property

Effect of the scanning path on the nanosecond pulse laser welded Al/Cu lapped joint