Abstract:Features and main technological methods of forming thin layers of semiconductor materials by methods of chemical deposition and mechanical application are analyzed. The disadvantages of thermal sputtering and cathodic sputtering of thin films in vacuum for multicomponent semiconductor compounds are indicated. Features of chemical deposition of semiconductor films from the gas (steam) phase are presented. Such deposition involves the transfer of source material from the evaporator zone with higher temperature in the form of volatile compounds to the colder surface of the substrate, where the film growth occurs as a result of reaction of transported compounds or their decomposition. It is shown that the growth of the film during chemical vapor deposition is a process of layer-by-layer condensation of atoms or molecules, with the advantageous difference that during chemical deposition the latter are formed as a result of a heterogeneous chemical reaction when there is no need for average free path length of the gas molecules to be larger than the size of the deposition chamber, i.e. no need for critical degree of vacuum. Chemical deposition of thin films from solution is characterized as a process of precipitation of solute which occurs due to the fact that the ionic product exceeds the product of solubility, i.e. it is greater than the constant value characteristic of a saturated solution in the equilibrium state. We emphasize, that chemical deposition from an water solution allows to obtain homogeneous in thickness and structure fine-grained non-textured mechanically stable polycrystalline films with good adhesion to substrates and the required set of properties. The method of pulverization with subsequent pyrolysis is described. This is deposition from intracomplex organometallic compounds, which is based on thermally stimulated reactions between clusters of atoms, chemically active substances of liquid or vapor phase. The method of electrolytic deposition on electrically conductive substrates is characterized. The method is using appropriate salt solutions by co-deposition of individual components, or by deposition on the cathode of one of the components with its subsequent interaction with others present in the solution. We also describe the method of obtaining epitaxial thin films of semiconductor deposition materials. We note that the analyzed methods or their modifications are necessary tool today to create thin-film semiconductor structures with predetermined properties. In the same time, in each particular case the features of each method of obtaining thin semiconductor films should be comprehensively evaluated and, depending on the chemical composition, structure, topology and complex of expected properties, the most effective method should be applied.

Substrate spacing and thin-film yield in chemical bath deposition of semiconductor thin films

High thin-film yield achieved at small substrate separation in chemical bath deposition of semiconductor thin films

Chemical deposition and mechanical application of semiconductors thin films

Comprehensive Analysis of CdS Ultrathin Films Modified by the Substrate Position inside the Reactor Container Using the CBD Technique

Effect of Bath Temperature on the Properties of CdS Thin Film Deposited by Chemical Bath Deposition

Influence of Deposition Time on Structural, Morphological, and Optical Properties of CdS Thin Films Grown by Low-Cost Chemical Bath Deposition

Deposition of Nanostructured CdS Thin Films by Thermal Evaporation Method: Effect of Substrate Temperature

Lattice mismatch as the descriptor of segregation, stability and reactivity of supported thin catalyst films

Preparation and Characterization of Cuins2 Thin Films for Solar Cells by Chemical Bath Deposition

Investigating the Effect of Steric Hindrance within CdS Single-Source Precursors on the Material Properties of AACVD and Spin-Coat-Deposited CdS Thin Films

Substrate and Cu concentration-dependent physical properties of spray-deposited Cu2ZnSnS4 thin films: a comparative study

Optical and Structural Characterization of Cd-Free Buffer Layers Fabricated by Chemical Bath Deposition

Nanocrystalline ZnS thin films by chemical bath deposition method and its characterization

Effects of substrate orientation and solution movement in chemical bath deposition on Zn(O,S) buffer layer and Cu(In,Ga)Se2 thin film solar cells

Determination of yielding and debonding in Al–Cu thin films from residual stress measurements via diffraction

Effect of molarity on the optical and structural properties of CdS thin films deposited by spray pyrolysis on flexible plastic substrates

Spectrum Analysis of Cds Thin Films Deposited by Chemical Bath Deposition with Ultrasonication

Geometry of Chemical Beam Vapor Deposition System for Efficient Combinatorial Investigations of Thin Oxide Films: Deposited Film Properties versus Precursor Flow Simulations

Thorough investigation of the optical, electrical and thermal properties of Cu3Se2 thin film deposited by chemical bath deposition

Numerical Simulation and Analytical Models for Thin Film CdTe Layers Deposited by an Inline AP-metalorganic Chemical Vapour Deposition Process

CdS THIN FILMS FABRICATED BY CHEMICAL BATH DEPOSITION