Abstract:The preparation and tribological properties of PAI/PI‐EPN polymer coatings. To improve the tribological properties of polar crane copper alloy bearings to withstand wear under dry sliding wear and grease lubrication at low temperatures, three kinds of coating materials modified by incorporating WS2 and SiC into polyamide‐imide/polyimide‐phenolic epoxy resin were designed. These composite coatings were sprayed on the surfaces of CuPb22.5Sn2.5 copper alloys by liquid spraying technique. Firstly, the tribological experiments were performed with three different coatings. Then, nanoindentation testing and wear morphology analysis were conducted. The results show that the hardness of the composite coatings decreases with the increase of WS2. As the content of WS2 increases, the coefficients of friction (CoFs) of coatings decreases under dry sliding wear. The S2 coating filled with 7.5 wt% WS2 exhibits the lowest wear rate and the best wear resistance under low temperature and dry sliding wear. The coatings form a lubricating film on the worn surface under dry sliding wear at −70°C, improving the wear resistance of the coatings. The primary wear mechanisms are adhesive wear and fatigue wear. The wear rates of the coatings increase with the increasing content of WS2 under low‐temperature grease lubrication. The S1 coating filled with 5.0 wt% WS2 exhibits the lowest wear. The S1 coating demonstrates a CoF of 0.07 and a wear rate of 6.5 × 10−6 mm3N−1 m−1 at 0°C, showing excellent friction‐reducing and wear‐resistant properties. The primary wear mechanism is adhesive wear. The wear mechanisms of polymer coatings are closely related to temperature. The dominant wear mechanisms transfer from abrasive wear to adhesive wear and fatigue wear under dry sliding wear and decreasing temperature. The wear mechanisms transfer from predominantly adhesive and abrasive wear to adhesive wear, fatigue wear, and abrasive wear under grease lubrication. The hardness of the coatings and the behavior of the polymer at various low temperatures are the primary factors that affect the differing wear mechanisms.

Influence of spraying perhydropolysilazane coating on friction and wear of end-face metal during the mixing process

Effects Of Polymer Composited Lubricant Coating On Tribological Properties Of Low-Carbon Steel Surface

Tribological properties of PEEK-based composite coating prepared by thermal spraying

The Effect of Different Dosages of TESPT on Metal Friction and Metal Wear in the Mixing Process

The investigation of tribological properties of PAI/PI‐EPN polymer coating filled with WS2 and SiC at low temperatures

Effect and performance analysis of different surface treatments on polymer-metal friction pairs

PREPARATION AND PROPERTIES OF HIGH TEMPERATURE SELF LUBRICATING COATINGS BY INDUCTION SINTERING

Friction and Wear Behavior of PTFE Coatings Modified with Poly (methyl Methacrylate)

Effects of fluorine and silicon components on the hydrophobicity failure behavior of acrylic polyurethane coatings

Fabrication and properties of a lubrication composite coating based on poly( p -hydroxybenzoic acid) (PHBA)

Preparation and Properties of PDMS Surface Coating for Ultra-Low Friction Characteristics

High Temperature Tribological Behavior of Electroless Plating Ni-P-Si3N4-WS2 Composite Coatings

Preparation of self‐healing hydrophobic coating and its anticorrosion property

Friction and Wear Performance of Composite SiC-YAG Thermal Spray Coatings in Water-Based Lubricants for Maritime Applications

Effect of hygrothermal aging on the friction behavior and wear mechanism of the multi-filler reinforced epoxy composites for coated steel

Effect of Phenolic Resin Coating Thickness on Mechanical Properties and Corrosion Resistance of Metal Materials

Effect of silane coating surface treatment on friction and wear properties of carbon fiber/PI composites

Ambient-curable polysiloxane coatings: structure and mechanical properties

Effect of Surface Modified Foamed Fe Powder on Tribological Properties of Semi-Metallic Friction Material

The influence of polydiethylsiloxane (PDES) concentration on the tribolfilm of chlorophenyl silicone oil (CPSO) under high-temperature lubrication

THREE-DIMENSIONAL SETUP OF COMPOSITE MATERIALS AS A WAY TO ACHIEVE HIGH MECHANICAL PROPERTIES