Abstract:Fluorinated organic-Inorganic hybrid materials were prepared using fluorine-containing monomers, silicone-containing monomers and tetraethyl orthosilicate by free-radical random copolymerization and sol-gel process, and applied as functional coatings onto aluminium alloy substrates. The fluorine-containing monomer used was dodecafluoroheptyl methyl acrylate (FA), and silicone-containing monomer used was vinyltriethoxy silane (VTES). Tetraethyl orthosilicate (TEOS) was added to pre-polymerized FA-co-VTES (PFAS) solution to cohydrolyze and co-condense with different addition values. The influence of inorganic component content (TEOS) on the physical properties of the coating films were characterized by FTIR, TGA, GPC, SEM, and XPS. The surface free energies of fluorinated organic-inorganic hybrid materials prepared were estimated from the contact angle data measured by sessile-drop method. Transparent coating films with smooth surface and uniform thickness could be obtained by the dip coating technique. FTIR and XPS results indicated that, owing to the strong electronegativity of the fluorine atoms, hydrophobic perfluoroalkyl groups were preferentially enriched to the outermost layer at the coating film-air interface, and three layers probably existed in the coating film. The upper layer oriented toward the air was composed of mainly perfluoroalkyl groups originating from FA, the intermediate layer was composed of hydrocarbon backbone chain originating from vinyl polymerization, and the bottom layer was composed of mainly -O-Si-O- network originating from TEOS. The fluorinated organic-inorganic hybrid materials prepared were very hydrophobic and exhibited excellent water repellency. It was demonstrated that the water repellency properties of PFAS/SiO2 hybrid materials was governed by hydrophobic perfluoroalkyl groups of the outermost layer. The contact angles of the coating films for water and methylene iodide were extremely high, at 120. 9 degrees and 93 degrees, respectively, for TEOS/FA mole ratios at 1 : 1, and their surface free energies were about 11.48 mJ/m(2). An important role of tetraethyl orthosilicate (TEOS) was to increase the density of the reaction sites of the -OH groups with the surface area and the thickness of fluorinated organic-inorganic hybrid coatings. It has been confirmed by FTIR and GPC results that the increase of TEOS amounts could enhance hydrolysis and condensation of alkoxide precursors to improve the adhesion between hybrid coating and aluminum substrates by the formation of Si-O-Al bonds. It was also testified that the increase of inorganic silica content had a significant effect oil the improvement of thickness of the bottom SiO2 layer, while it had a slight influence on the surface wettability of the hybrid coatings. The useful properties of fluorinated organic-inorganic hybrid coatings like better thermal stability and improved corrosion resistance,could be significantly enhanced by the improvement of thickness of the bottom SiO2 layer and bonding between SiO2 layer and aluminum substrates. Morphology analysis by SEM showed that the introduction of flexible organic phase could relax the stress and reduce the microcracks caused by the volume shrinkage of silicon network during heat treatment process. The thermal stability of fluorinated organic-inorganic hybrid materials studied by using TGA technique could be improved with TEOS amounts.The burning temperature should be less than 290 degrees C because the perfluoroalkyl groups begin to decompose from this temerature.

Effects of fluorine and silicon components on the hydrophobicity failure behavior of acrylic polyurethane coatings

Preparation of Fluorinated and Silicone Acrylic Polyurethane Coatings and Their Environmental Behaviors

Preparation and hydrophobicity failure behavior of two kinds of fluorine-containing acrylic polyurethane coatings

Preparation and Failure Behavior of Fluorine-Containing Acrylic Polyurethane Coating

Hydrophobicity and corrosion resistance of waterborne fluorinated acrylate/silica nanocomposite coatings

Synthesis and characterization of acrylic latex: Effects of fluorine and silicon components on properties of the latex copolymers

Research of Fluorine-Modified Two Component Waterborne Acrylic Polyurethane Coating Performance

Fluoroalkyl trimethoxysilane route to hydrophobic 2K polyurethane clearcoats and their failure mechanism

Synthesis and Surface Properties of Fluorinated Organic-Inorganic Hybrid Coatings

Synthesis Of Fluoroalkyl-Modified Polyester And Its Application In Improving The Hydrophobicity And Oleophobicity Of Cured Polyester Coatings

Preparation and Characterization of the Cross-Linked Fluoro-Silicon Polyacrylate–Polyurethane Hybrid Emulsions for Superior Performance of Waterborne Coatings

Study on the morphology and tribological properties of acrylic based polyurethane/fumed silica composite coatings

Synthesis Of Fluorosilicone Monomer And Application In Hydrophobic Surface Of Acrylic Copolymer

Influence of Fluorine Incorporation into Waterborne Acrylic Coatings on Resulting Hydrophobic, Thermal Stability and Drag- Reduction Properties

Preparation of UV-Curable Low Surface Energy Polyurethane Acrylate/Fluorinated Siloxane Resin Hybrid Coating with Enhanced Surface and Abrasion Resistance Properties

Influence of Fluorine-Containing Monomer Content on the Hydrophobic and Transparent Properties of Nanohybrid Silica Polyacrylate Coating Materials

Surface topography and hydrophobicity of waterborne fluorinated acrylic/silica hybrid coatings

Study on the Anti-Abrasion Resistance of Superhydrophobic Coatings Based on Fluorine-Containing Acrylates with Different T-g and SiO2

Preparation and Characterization of Fluorinated Acrylate and Epoxy Co-Modified Waterborne Polyurethane

Preparation of Superhydrophobic Coating from Fluorine-Containing Acrylate Polymer and Polysiloxane with Nano-SiO2

Synthesis and Properties of Fluoropolyacrylate Coatings