Abstract:Owing to its outstanding and superior properties, alumina is a well-documented advanced ceramic to realize numerous manufacturing and medical applications. However, machining alumina using traditional techniques is difficult, time-consuming, and sometimes impossible due to its high hardness, brittleness, and low electrical and thermal conductivity. Rotary Ultrasonic Machining (RUM) is among the most frequently reported methods for drilling holes in ceramics. However, extensive edge chipping is also noticeable in RUM both at the entrance and at the exit of the hole if correct machining variables are not considered. This research, therefore, focuses on experimentally exploring the significance of RUM control variables, notably: spindle speed, feed rate, ultrasonic amplitude, and ultrasonic frequency on edge chipping and surface roughness. The experiments are planned through the response surface methodology, which is dependent on a central composite rotatable design. The distinctive selection of RUM parameters that mitigate edge chipping may produce unfavorable outcomes for the surface finish. This assumption underlines the necessity of multi-objective optimization to ensure competitive RUM efficacy for hole drilling in alumina. A gray relational analysis paired with a principal component analysis (GRA–PCA) framework is embraced to identify optimal drilling variables for RUM. The procedure of optimizing multiple quality attributes (edge chipping and surface roughness) to elevate the quality of hole drilling in alumina ceramic using the GRA–PCA method is illustrated. According to this study, the feed, along with speed, amplitude, and frequency, has the biggest impact on RUM efficacy. The findings of this investigation reveal that the minimal surface roughness ( R a = 0.29 μm and R t = 1.19 μm) and lowest area of edge chipping at the hole entrance and exit (0.29 mm 2 and 1.36 mm 2 , respectively) can be achieved using the following parameters: speed −6000 rpm, feed rate −0.5 mm/min, amplitude −35 μm, and frequency −23 kHz.

Rotary ultrasonic drilling of polyetherimide composite to enhance the surface roughness and MRR: Experimental investigations and statistical approach

In-situ temperature monitoring during rotary ultrasonic-assisted drilling of fiber-reinforced composites

A New Strategy of Carbon Fiber Reinforced Plastic Drilling Evaluation Using Thermal Measurement

Multi‐objective optimization of ultrasonic vibration‐assisted drilling in carbon fiber reinforced polyetherketoneketone laminate

Experimental investigation and parametric optimization of rotary ultrasonic machining of different bio-ceramic materials

Cutting force and specific energy for rotary ultrasonic drilling based on kinematics analysis of vibration effectiveness

Cutting force, Vibration, and Temperature in Drilling on a Thermoplastic Material of PEEK

Optimization of control variables in rotary ultrasonic machining of alumina ceramic for reduced edge chipping and enhanced surface finish

Improving hole exit quality in rotary ultrasonic machining of ceramic matrix composites using a compound step-taper drill

IMPROVEMENT OF SURFACE PROPERTIES OF CARBON FIBER REINFORCED EPOXY COMPOSITES USING SOLID LUBRICANTS DURING MACHINING PROCESSES

Optimizing Process Parameters in Drilling of CFRP Laminates: A Combined MOORA–TOPSIS–VIKOR Approach

Investigation of delamination and surface quality of machined holes in drilling of multiwalled carbon nanotube doped epoxy/carbon fiber reinforced polymer nanocomposite

An Experimental Study on Rotary Ultrasonic Drilling Small-Diameter Holes of High Volume Fraction Silicon Carbide-Reinforced Aluminum Matrix Composites (Sicp/al)

Effects of Drilling Parameters on Drilling of PEEK-CF30 Thermoplastic Material: Thrust Force, Surface Roughness and Delamination

Rotary ultrasonic machining of CFRP composites: a study on power consumption

Experimental investigation on mechanical performance and drilling behavior of hybrid polymer composites through statistical and machine learning approach

Impact Of Drilling Parameters On The Surface Roughness Of Egg Shell Filled Glass Fibre / Polyester Composites

Surface Treatment of Additively Manufactured Polyetheretherketone (PEEK) by Centrifugal Disc Finishing Process: Identification of the Key Parameters

Drilling characteristics of carbon/epoxy and carbon/polyimide composites

CFRP composite drilling through electrical discharge machining using aluminum as fixture plate

Statistical modelling and assessment of surface roughness in drilling of hybrid fiber composite