Abstract:A new strategy; cation and anion dual gradient, is proposed and successfully constructed at the surface of LiCoO2 to minimize the highly oxidized Co4+ and O− species when charged to high potentials, which not only suppresses the relevant surface side reactions, but also affected the Li+ diffusion kinetics through the induced spinel‐like surface structure, making LiCoO2 exhibit excellent cycling stability and rate capability at the high cutoff voltage of 4.6 V, further validated in the 4.55 V pouch full cell (equivalent to 4.6 V vs Li/Li+).LiCoO2 (LCO) is the most successful cathode material for commercial lithium‐ion batteries. Cycling LCO to high potentials up to 4.5 V or even 4.6 V can significantly elevate the capacity but cause structural degradation due to the serious surface side reaction between the highly oxidized Co4+ and O− species with organic electrolytes. To tackle this concern, a new strategy, constructing cation and anion dual gradients at the surface of LCO (DG‐LCO), is proposed. Specifically, the electrochemically inactive cation and anion are selected to substitute Co3+ and O2− at the surface in a gradated manner, thus minimizing the highly oxidized Co4+ and O− species at high potentials and suppressing the induced surface side reactions. Unexpectedly, this dual gradient design leads to a spinel‐like surface structure coherently with bulk layered structure, which facilitates Li+ diffusion kinetics. Thus, DG‐LCO achieves high capacity and excellent cycling stability at 4.6 V (≈216 mA h g−1 at 0.1 C, a capacity retention of 88.6% after 100 cycles in 1.8 A h pouch full cell at 1 C), as well as improved rate capability (≈140 mA h g−1 at 5 C). These studies provide useful guidelines for future design of cathode materials with long lifespan and high rate capability.

Highly Stable 4.6 V LiCoO2 Cathodes for Rechargeable Li Batteries by Rubidium‐Based Surface Modifications

Mixed Lithium Ion and Electron Conducting LiAlPO 3.93 F 1.07 -Coated LiCoO 2 Cathode with Improved Electrochemical Performance

Lithium-Aluminum-Phosphate Coating Enables Stable 4.6 V Cycling Performance of LiCoO2 at Room Temperature and Beyond

Operating Highly Stable LiCoO2 Cathodes up to 4.6 V by Using an Effective Integration of Surface Engineering and Electrolyte Solutions Selection

Enhanced Interfacial and Cycle Stability of 4.6 V Licoo2 Cathode Achieved by Surface Modification of Kalf4

Stable LCO Cathodes Charged at 4.6 V for High Energy Secondary Li‐ion Batteries by One‐Pot Dual Metal Fluorides Coating

Stabilizing 4.6 V LiCoO2 via Surface‐to‐Bulk Titanium Modification

Scalable Precise Nanofilm Coating and Gradient Al Doping Enable Stable Battery Cycling of LiCoO2 at 4.7 V

Surface engineering of LiCoO2 by a multifunctional nanoshell for stable 4.6V electrochemical performance

Stabilizing LiCoO<sub>2</sub> at 4.6 V by regulating anti-oxidative solvents

Realizing long-term cycling stability and superior rate performance of 4.5 V–LiCoO2 by aluminum doped zinc oxide coating achieved by a simple wet-mixing method

Improving Stability of High Voltage LiCoO2 by Synergetic Surface Modification Via in Situ Surface Conversion

Stabilizing LiCoO2 at 4.6 V by regulating anti-oxidative solvents

Surface Design with Cation and Anion Dual Gradient Stabilizes High‐Voltage LiCoO 2

Bimetallic synergistic modified layer promotes the cyclic stability of LiCoO 2 under 4.6 V high voltage

Multiple Surface Optimizations for a Highly Durable LiCoO2 beyond 4.6 V

Densification of Cathode/Electrolyte Interphase to Enhance Reversibility of LiCoO<sub>2</sub> at 4.65 V

Stable Cycling of LiCoO2 at 4.55 V Enabled by Combined Mg Doping and Surface Coating of NASICON-type Electrolyte

Ultrathin Dense LiF Coverage Coupled with a Near-Surface Gradient Fluorination Lattice Enables Fast-Charging Long-Life 4.6 V LiCoO2

Tuning Surface Chemistry to Reduce the Step-Like Degradation of LiCoO2 at 4.6 V

Highly stable operation of LiCoO2 at cut-off ≥ 4.6 V enabled by synergistic structural and interfacial manipulation