Abstract:A new strategy; cation and anion dual gradient, is proposed and successfully constructed at the surface of LiCoO2 to minimize the highly oxidized Co4+ and O− species when charged to high potentials, which not only suppresses the relevant surface side reactions, but also affected the Li+ diffusion kinetics through the induced spinel‐like surface structure, making LiCoO2 exhibit excellent cycling stability and rate capability at the high cutoff voltage of 4.6 V, further validated in the 4.55 V pouch full cell (equivalent to 4.6 V vs Li/Li+).LiCoO2 (LCO) is the most successful cathode material for commercial lithium‐ion batteries. Cycling LCO to high potentials up to 4.5 V or even 4.6 V can significantly elevate the capacity but cause structural degradation due to the serious surface side reaction between the highly oxidized Co4+ and O− species with organic electrolytes. To tackle this concern, a new strategy, constructing cation and anion dual gradients at the surface of LCO (DG‐LCO), is proposed. Specifically, the electrochemically inactive cation and anion are selected to substitute Co3+ and O2− at the surface in a gradated manner, thus minimizing the highly oxidized Co4+ and O− species at high potentials and suppressing the induced surface side reactions. Unexpectedly, this dual gradient design leads to a spinel‐like surface structure coherently with bulk layered structure, which facilitates Li+ diffusion kinetics. Thus, DG‐LCO achieves high capacity and excellent cycling stability at 4.6 V (≈216 mA h g−1 at 0.1 C, a capacity retention of 88.6% after 100 cycles in 1.8 A h pouch full cell at 1 C), as well as improved rate capability (≈140 mA h g−1 at 5 C). These studies provide useful guidelines for future design of cathode materials with long lifespan and high rate capability.

Enhanced Interfacial and Cycle Stability of 4.6 V Licoo2 Cathode Achieved by Surface Modification of Kalf4

Mixed Lithium Ion and Electron Conducting LiAlPO 3.93 F 1.07 -Coated LiCoO 2 Cathode with Improved Electrochemical Performance

Highly Stable 4.6 V LiCoO2 Cathodes for Rechargeable Li Batteries by Rubidium‐Based Surface Modifications

Enhanced 4.7 V Electrochemical Performance of the LiCoO2 Cathode Via a Fluoride and LiCo1–xAlxO2 Composite Coating

Lithium-Aluminum-Phosphate Coating Enables Stable 4.6 V Cycling Performance of LiCoO2 at Room Temperature and Beyond

Operating Highly Stable LiCoO2 Cathodes up to 4.6 V by Using an Effective Integration of Surface Engineering and Electrolyte Solutions Selection

Realizing long-term cycling stability and superior rate performance of 4.5 V–LiCoO2 by aluminum doped zinc oxide coating achieved by a simple wet-mixing method

Superior stable high‐voltage LiCoO2 enabled by modification with a layer of lithiated polyvinylidene fluoride‐derived LiF

Stable LCO Cathodes Charged at 4.6 V for High Energy Secondary Li‐ion Batteries by One‐Pot Dual Metal Fluorides Coating

Improving diffusion kinetics and phase stability of LiCoO2 via surface modification at elevated voltage

Enhanced cycle stability of LiCoO2 at high voltage by mixed conductive Li7.5La3Zr1.5Co0.5O12 coating

Enhanced Interfacial Kinetics and High-Voltage/High-Rate Performance of Licoo2 Cathode by Controlled Sputter-Coating with A Nanoscale Li4ti5o12 Ionic Conductor

Improved Cycling Stability of LiCoO2 at 4.5 V Via Surface Modification of Electrodes with Conductive Amorphous LLTO Thin Film

Anticorrosive nanosized LiF thin film coating for achieving long-cycling stability of LiCoO2 at high voltages

Simultaneously Constructing a TiO2–LiF Composite Coating Enhancing the Cycling Stability of LiCoO2 at 4.6 V High Voltage

Stabilizing 4.6 V LiCoO2 via Surface‐to‐Bulk Titanium Modification

A Surface Modification Layer with Cobalt Aluminate Inhibits 4.6 V High-Voltage Phase Transition of LiCoO2

Epitaxial growth of a single hexagonal layered α-LiAlO2 coating on a high-voltage LiCoO2 cathode material for enhanced stability

Ultrathin Titanium Dioxide Coating Enables High-Rate and Long-Life Lithium Cobalt Oxide

Surface Design with Cation and Anion Dual Gradient Stabilizes High‐Voltage LiCoO 2

A surface modification layer with cobalt aluminate inhibits 4.6 V high-voltage phase transition of LiCoO 2