Abstract:The moving bed biofilm reactor (MBBR) has certain advantages, such as high wastewater treatment efficiency, low maintenance and operating costs, and simple operation. It has emerged as a valuable option for small decentralized facilities. The filling ratio, aeration mode and aeration intensity are the main factors that affect the performance of MBBRs in wastewater treatment. However, the information that concerns the used criteria that pertain to the process design for the MBBR is not adequate. In this study, a three dimensional computational fluid dynamics (CFD) model was constructed and the maximum error was only 1.98%, which was much smaller than the traditional 2D-CFD model. The filling ratio, aeration mode and aeration intensity of MBBR were optimized by CFD model from the point of view of fluid mechanics. The results show that the fluidization performance of the filling is the best under the one-side aeration mode with 30% filling ratio. The cost-performance ratio of the reactor with 30% filling ratio was 1.53, 25% and 35% filling ratio were only 1.17 and 1.14 respectively. Increasing the aeration intensity could improve the fluidization performance. However, the effect of high aeration intensity on the fluidization performance of the carrier was limited and the energy consumption increased greatly. The results revealed that when the aeration intensity increased from 0.07 min-1 to 0.13 min-1, the proportion of the carrier area increased by 16.56%. The proportion of the carrier area with an aeration rate of 0.20 min-1 was only 4.23%, which is higher than 0.13 min-1. The main factors that control the fluidization of the carrier were the range of the flow zone and the flow velocity of the liquid. Increasing the range of the flow zone could facilitate the flow of the carriers. The critical value of the flow velocity of the liquid in the flow zone was 0.04 m/s. These results could guide the optimization design of the filling ratio and the aeration conditions and provide a theoretical basis for the application of MBBR.

CFD-PBM simulations the effect of aeration rates on hydrodynamics characteristics in a gas-liquid-solid aerobic fluidized bed biofilm reactor

Effect of Agitation on the Fluidization Behavior of a Gas–solid Fluidized Bed with a Frame Impeller

CFD Simulation of an Agitated Gas-Fluidized Bed: Effects of Particle–particle Restitution Coefficient on the Hydrodynamics

Multi-scale Characteristics and Gas-Solid Interaction among Multiple Beds in a Dual Circulating Fluidized Bed Reactor System

Gas bubble behaviors in a gas–solid fluidized bed with an arch agitator

CFD Simulation and Experiments of Dynamic Parameters in Gas–solid Fluidized Bed

Dynamic Modelling of Fluidisation in Gas-Solid Bubbling Fluidised Beds

CFD simulation for comparative of hydrodynamic effects in biochemical reactors using population balance model with varied inlet gas distribution profiles

Numerical study of hydrodynamic characteristics in a moving bed biofilm reactor

Experimental Study and Numerical Simulation of Gas–Liquid Two-Phase Flow in Aeration Tank Based on CFD-PBM Coupled Model

Impact of the Reactor Structure on Biomass Pyrolysis in Fluidized-Bed Reactors: A Coarse-Grained CFD-DEM Study

Experimental Research on the Gas-Solid Flow Characteristics in Large-Scale Dual Fluidized Bed Reactor

Bubble Dynamics and Particle Orientation in a Binary Fluidized Bed Containing Spherocylinders and Spheres

Multi-Scale Simulation of Biomass Gasification in Fluidized Beds

An Improved Computational Fluid Dynamics-Discrete Bubble Model for Multiphase Bubble Flow Simulation with a Wide Grid/bubble Size Ratio

Fluidization Dynamics in an Impinging-jet-driven Bioreactor for Artificial Liver System

Characteristics of oxygen mass transfer and its impact on pollutant removal performance and microbial community structure in an aerobic fluidized bed biofilm reactor for treatment of municipal wastewater

Influence of Hydrodynamics on the Performance of a Biofilm Airlift Suspension Reactor

Research on the influence of aeration manners on the mass transfer characteristics of bubbles in multi‐column airlift photobioreactor

Numerical Simulation Study on the Gas–Solid Flow Characteristics of a Large-Scale Dual Fluidized Bed Reactor: Verification and Extension

CFD–PBM Simulation on Bubble Size Distribution in a Gas–Liquid–Solid Flow Three-Phase Flow Stirred Tank