Abstract:With the development of the aerospace industry, the close exploration of the Sun has become a human demand. However, close-range exploration means that the detection satellite needs to accept the test of high temperatures above 1400 °C, so a thermal protective coating is a necessary part of the detection satellite to isolate heat and reflected light. Al2O3 coating has the characteristics of high emissivity and low absorptivity, and it is the best choice for thermal protection coating. However, the coating is subjected to thermal cycles, including heating and cooling, as the satellite rotates around the Sun, which could result in a change in the structure and properties of the coating. Therefore, thermal shock experiments were carried out, and the influence of microstructure on the absorption rate of the Al2O3 coating was investigated. In this study, an Al2O3 coating was prepared by atmospheric plasma spraying (APS). The coating was subjected to a thermal shock (TS) test at 1400 °C using a self-made flame shock device, and coating samples under different thermal shock degrees were obtained. A scanning electron microscope (SEM) was used to characterize the coating pores, and the effects of the coating pore size, aspect ratio (A/R) and cracks in the coating on the optical properties of the coating under different thermal shock degrees were analyzed. In order to clarify the influence of coating microstructure changes on the optical properties of the coating under different thermal shock degrees, not only relevant experiments were carried out, but also the solar reflectivity of Al2O3 coatings with different pore structures was analyzed by the finite element method using finite-difference time-domain (FDTD). The results show that increasing the porosity and aspect ratio of the pores can improve the partial solar absorption of the coating. It was also found that the transverse crack propagation improves the solar reflectance of the coating.

Preparation and thermal shock resistance of solar thermal absorbing corundum ceramics for concentrated solar power

The microstructures and properties of Fe2O3 and TiO2 co-doped corundum ceramics for solar thermal absorbing materials

Scalable All-Ceramic Nanofilms As Highly Efficient and Thermally Stable Selective Solar Absorbers

Preparation and characterization of corundum ceramics doped with Fe2O3 and TiO2 for high temperature thermal storage

Preparation and characterization of mullite-silicon carbide heat absorbing ceramics for solar thermal tower plant

Thermal shock resistance and oxidation resistance of MgAl2O4–Si3N4 ceramics for solar thermal absorber: The effects of TiO2 additive content

Preparation and Thermal Shock Resistance of Mullite Ceramics for High Temperature Solar Thermal Storage

High-Performance Spectrally Selective Absorber Using the ZrB2-Based All-Ceramic Coatings.

An Ultra-High Temperature Stable Solar Absorber Using the ZrC-Based Cermets

Microstructure and performances of Gd2O3-added corundum–mullite ceramic composites for concentrated solar power applications

High-Performance Spectrally Selective Absorber Using the ZrB 2 -Based All-Ceramic Coatings

Titanium diboride ceramics for solar thermal absorbers

High-temperature stability of Cu–20Si alloy-corundum ceramic composite thermal storage materials

Enhanced Performance of High Temperature Aluminate Cementitious Materials Incorporated with Cu Powders for Thermal Energy Storage

Reinforcement optical performance and thermal tolerance in a TiB2-HfB2-based double-layer spectral selective absorber via a pre-annealing strategy

Effect of High-Temperature Thermal Shock on Solar Absorption Rate of Alumina Coating

Surface Reconstruction of La0.5Sr0.5CoO3-δ Ceramic toward High Solar Selectivity for High-Temperature Air-Stable Solar-Thermal Conversion

Optical characterization of hafnium boride and hafnium carbide-based ceramics for solar energy receivers

Study on Thermal Shock Resistance and Oxidation Resistance of Ultra-High Temperature Ceramics

Thermal Properties of Nano-Sio2 Optimized Aluminate Cementitious Composite Cu Powders

Optical, Structural and Thermal Characteristics of Cu–CuAl2O4 Hybrids Deposited in Anodic Aluminum Oxide As Selective Solar Absorber