Abstract:This paper aims to understand the influence of microalloying constituents (Ti, Zr, Sr and Sc), and three heat treatment conditions i.e., T6, retrogression and reaging (RRA) and high temperature aging (HTA) on mechanical and thermal characteristics of modified Al-Zn-Mg-Cu-X alloy using microstructural analyses consist of precipitation characteristics, phase fraction and phase morphology. Addition of 0.25 wt % Sc significantly refines the grain structure , reducing the grain size from 62 μm to 34 μm and increasing Al 3 Zr, Al 3 (Zr, Ti), and Al 3 (Sc, Zr) precipitate fraction. After T6 aging, the alloy exhibits primary precipitates of fine η and T phases, accompanied by secondary intermetallics as well as S phases. RRA treatment led to a slightly larger fraction of coarse Zn and Cu-rich phases, while HTA results in larger η, T, and S phases due to high-temperature aging. The addition of Sc reduces the cooling rate by raising the transition temperature to 532 °C with an enthalpy of 22.1 J/g. T6 treatment shows dissolution of most η phases within the matrix, although RRA and HTA exhibit higher enthalpy due to a greater fraction of η phases. The tensile strength of Al-Zn-Mg-Cu-X alloy follows the following sequence: T6 > RRA > HTA > as-cast condition, regardless of micro-alloy additions. Under T6 conditions, Sc added alloy achieves 30 % higher strength, i.e., 575 MPa, than base alloy due to fine dispersoids. RRA treatment enhances elongation without compromising mechanical properties , resulting in a shift from transgranular brittle fracture to intergranular-dominated mix-mode fracture, with the presence of secondary cracking.

Enhancement of the Electrical Conductivity and Mechanical Properties of Al-Mg-Si and Al-Mg-Zn Ternary Systems After a T8 Heat Treatment

Evolution of microstructure, mechanical properties and corrosion behavior of Al-4Mg-2Zn-0.3Ag (wt.%) alloy processed by T6 or thermomechanical treatment

Microstructural Evolution and Mechanical Properties of Cast Al-2Li-2Cu-0.5Mg-0.2Zr Alloy During Heat Treatment

Effect of Heat Treatment on the Microstructure and Mechanical Properties of Extruded Al–4Cu–1Li–0.4Mg–0.4Ag–0.18Zr Alloy

Effect of heat treatment on the microstructure and mechanical properties of Al‐9Si‐0.4Mg‐0.1Cu alloy

Microstructure characteristics of an ultra-high strength extruded Al-4.7Cu–1Li-0.5Mg-0.1Zr–1Zn alloy during heat treatment

Enhancing properties of Al-Zn-Mg-Cu alloy through microalloying and heat treatment

Microstructural Characteristics and Mechanical Properties of Extruded Al-4Cu-1Li-0.4Mg-0.1Zr-xZn Alloy

Effects of heat treatment and testing temperature on the tensile properties of Al–Cu and Al–Cu–Si based alloys

Microstructure and Mechanical Properties of Cast Al-Li-Mg Alloy: Role of Cu Addition and Heat Treatment

Achievement of High Strength and Ductility in Al–Si–Cu–Mg Alloys by Intermediate Phase Optimization in As-Cast and Heat Treatment Conditions

Balance of Mechanical Properties of Mg-8Li-3Al-2Zn-0.5Y Alloy by Solution and Low-Temperature Aging Treatment

Enhanced strength and electrical conductivities of an Al-Zn-Mg aluminum alloy through a new aging process

Effect of short T6 heat treatment on the microstructure and the mechanical properties of newly developed die-cast Al–Si–Mg–Mn alloys

Microstructure, Mechanical Properties and Corrosion Behaviors of Al–Li–Cu–Mg–Ag–Zn Alloys

Effects of Solution Treatment on the Microstructure, Tensile Properties, and Impact Toughness of an Al–5.0Mg–3.0Zn–1.0Cu Cast Alloy

Effect of heat treatments on microstructure and mechanical properties of sand cast Al–2Li–2Cu–0.5Mg–0.2Sc–0.2Zr alloy

Enhanced elevated-temperature mechanical properties of hot-rolled Al–Cu alloys: effect of zirconium addition and homogenization

On the Role of Al-B Master Alloy and Heat Treatment on Synergistic Improvement in Electrical Conductivity and Hardness of Al-Mg-Si Alloys

Tailoring the mechanical properties and thermal stability of additive manufactured micro-alloyed Al-Cu alloy via multi-stage heat treatment

The development of low-temperature heat-treatable high-pressure die-cast Al–Mg–Fe–Mn alloys with Zn