Abstract:Integrating phase change materials (PCMs) with concentrated photovoltaic-thermoelectric (PV-TE) systems can effectively control the interface temperature between PV and TE components and improve the full solar-spectrum utilization efficiency. However, since the structure of photovoltaic-phase change material-thermoelectric (PV-PCM-TE) systems is complex and the temperatures among the components are coupled and affect each other, the photo-thermal-electric conversion characteristics under the actual physical properties need to be analyzed by a more detailed model, and the suitable operating conditions for PV-PCM-TE systems remain clear. There is still a lack of the method for improving the system performance. Therefore, a three-dimensional transient model is established herein by combining the Monte Carlo ray-tracing method and finite volume method to simulate the complex energy conversion processes of the PV-PCM-TE system. Based on this, performances of PV-PCM-TE, PV-TE, and PV systems are compared under different operating conditions, and the applicable conditions for PV-PCM-TE systems are analyzed. Then effects of key parameters of the phase change module are investigated. In the end, to further improve the system performance, a partition screening method of PCM is proposed considering the nonuniform solar radiation on photovoltaic surfaces, and the selection and layout area of PCMs are optimized. The results present that the applicable operating conditions are low concentration ratio (< 20) and low heat transfer coefficient (< 20 W·m-2·K-1). In terms of structural parameters, the system power generation is most significantly affected by the width. In terms of PCM physical properties, it is most affected by the PCM density, followed by latent heat. For different concentration ratios, there are different optimal melting points to achieve the highest power generation. The proposed PCM partition screening method can efficaciously control PV-TE interface temperature, and reduce photovoltaic cells' temperature by 47°C. The system efficiency can be increased by 4.8% and 4.2% after the optimization compared with that of the single PV cell and the traditional PV-TE system, respectively.

Numerical Analysis of the Influence of Trapezoidal Geometry in Phase Change Material Containers on Temperature Distribution in Concentrated Photovoltaic Panel Cooling

Performance evaluation and thermal stabilization of photovoltaic panels using phase-change materials

A Parametric Study about the Potential to Integrate Phase Change Material into Photovoltaic Panel

Numerical Study on 2-Stage Phase Change Heat Sink for Cooling of Photovoltaic Panel

Thermal evaluation of photovoltaic panels combined pulsating heat pipe with phase change materials: numerical study and experimental validation

Experimental and numerical study on performance enhancement of photovoltaic panel by controlling temperature with phase change material

MODEL DEVELOPMENT AND PERFORMANCE IMPROVEMENT OF A PHOTOVOLTAIC-THERMOELECTRIC SYSTEM BY INTEGRATING AND OPTIMIZING PHASE CHANGE MATERIALS

Numerical Study on Using Multichannel Tube and PCM for Improving Thermal and Electrical Performance of a Photovoltaic Module

Effect of varying the thermophysical properties of phase change material on the performance of photovoltaic/thermal-PCM hybrid module numerically

Experimental Study and Performance Analysis on Solar Photovoltaic Panel Integrated with Phase Change Material

Annual performance study and optimization of concentrated photovoltaic-phase change material system

Annual Thermal Management of the Photovoltaic Module to Enhance Electrical Power and Efficiency Using Heat Batteries

Investigation on Designed Fins-Enhanced Phase Change Materials System for Thermal Management of a Novel Building Integrated Concentrating PV

Numerical investigation of the effect of operating conditions on performance of PV-PCM system

Research and numerical analysis on performance optimization of photovoltaic-thermoelectric system incorporated with phase change materials

Numerical study on the performance of a glazed photovoltaic thermal system integrated with phase change material (GPVT/PCM): on the contribution of PCM volumetric fraction and environmental temperature

Operational and structural parametric analysis of a photovoltaic/thermal system integrated with phase change material

Comparative study on heat transfer characteristics of molten PCM in PV/PCM air-based system based on grey relation analyses

Experimental, numerical, and 4E assessment of photovoltaic module using macro-encapsulation of pure and nano phase change material: A comparative analysis

Thermal analysis of solar panel with phase change material: experimental and numerical study

Thermal management enhancement of photovoltaic panels using phase change material heat sinks with various T-shaped fins