Abstract:Solar radiation is captured by photovoltaic (PV) panels, which use it to create electricity. However, an overabundance of photons striking the PV's surface raises its temperature, which lowers its efficiency. These days, cooling solar panels is very important, and research on these methods is widely available in the literature. Thus, the study field's problems truly lie in developing new or improved methods for doing the same tasks. The goal of this work is to further boost the efficiency of photovoltaic (PV) panels beyond what can be achieved with PCM and free/forced convection alone. To do this, phase change materials (PCM) are cooled using both free and forced convection. In accordance with the latitude of Lebanon's Bekaa Valley, four cooling techniques are experimentally investigated. A photovoltaic panel using phase-change material (PCM) with copper and aluminum wires in a 70 %–20 %–10 % mass ratio (CPCM-PV), respectively, is the first cooling method. In the second approach, four 5 cm long fins are fixed under free convection using the same combination of aluminum fins inside the PCM container while preserving the same ratio (IEF-PCM-Free-PV). The third technique is the same as the second but with forced convection (IEF-PCM-Forced-PV), while the fourth technique uses an aluminum finned plate with 16 finned plates under forced convection (F-Forced-PV). IEF-PCM-Forced-PV showed the most relative increases in efficiency rate of energy dissipated of 20.36 % and 62.24 %, respectively, as compared to the regular PV panel, according to the results. F-Forced-PV, IEF-PCM-Free-PV, and CPCM-PV showed an increase in relative efficiency of 16.87 %, 6.3 %, and 3.9 % respectively, and correspondingly, these enhancements were accompanied by an increase in energy dissipation of 55.80 %, 44.85 %, and 41.18 % for each system. Economically, the IEF-PCM-Forced-PV had the highest total yearly savings of $17.87 with a payback period of 1.9 years. An appropriate transient energy balance is conducted and permitted to demonstrate clearly the transient behavior of the system under the various cooling techniques. Finally, the percentage of enhancement using the newly suggested composite PCM with internal and external fins under forced convection is compared to the enhancement found in the literature for various classical techniques and shows greater potential for further enhancement of the PV performance.

Thermal management enhancement of photovoltaic panels using phase change material heat sinks with various T-shaped fins

Heat-dissipation performance of photovoltaic panels with a phase-change-material fin structure

Investigation on Designed Fins-Enhanced Phase Change Materials System for Thermal Management of a Novel Building Integrated Concentrating PV

Numerical investigation of thermal management performances in a solar photovoltaic system by using the phase change material coupled with bifurcated fractal fins

Numerical study of phase change material partitioned cavities coupled with fins for thermal management of photovoltaic cells

Experimental study of phase change material heat sinks coupled with Cantor fractal fins for thermal management of photovoltaic systems

Evaluating the Impacts of Fin Structures and Fin Counts on Photovoltaic Panels Integrated with Phase Change Material

Investigation on the Melting Performance of a Phase Change Material Based on a Shell-and-Tube Thermal Energy Storage Unit with a Rectangular Fin Configuration

Thermal evaluation of photovoltaic panels combined pulsating heat pipe with phase change materials: numerical study and experimental validation

Experimental Study on the Performance of a Solar Photovoltaic/thermal System Combined with Phase Change Material

Efficiency improvement of PV module using a binary-organic eutectic phase change material in a finned container

Investigation of phase change heat transfer in a rectangular case as function of fin placement for solar applications

Performance improvement of solar PV module through hybrid cooling system with thermoelectric coolers and phase change material

A comprehensive experimental study of cooling photovoltaic panels using phase change materials under free and forced convection – Experiments and transient analysis

Numerical Study on 2-Stage Phase Change Heat Sink for Cooling of Photovoltaic Panel

A Parametric Study about the Potential to Integrate Phase Change Material into Photovoltaic Panel

Influence on solar PV performance integrated with heat sinks and nano-enhanced phase change material

Experimental and numerical study on performance enhancement of photovoltaic panel by controlling temperature with phase change material

Thermal management of solar photovoltaic module by using drilled cylindrical rods integrated with phase change materials

Photovoltaic Cooling Utilizing Phase Change Materials

Numerical and Experimental Study on Temperature Control of Solar Panels with Form-Stable Paraffin/expanded Graphite Composite PCM