Abstract:PURPOSEHigh-sensitivity and high-resolution depth-encoding positron emission tomography (PET) detectors are required to simultaneously improve the sensitivity and spatial resolution of a PET scanner so that the quantitative accuracy of PET studies can be improved. The semi-monolithic scintillator PET detector has the advantage of measuring the depth of interaction with single-ended readout as compared to the traditional pixelated scintillator detector, and significantly reducing the edge effect that deteriorates the spatial resolution at edges of the detector as compared to the monolithic scintillator detector if a long rectangular semi-monolithic detector is used. In this work, depth-encoding PET detector modules were built by using long rectangular semi-monolithic scintillators and single-ended readout by silicon photomultiplier (SiPM) arrays. The performance of the detector modules was measured.METHODSThe rectangular semi-monolithic scintillator detector has an outside dimension of 11.6 × 37.6 × 10 mm3 and consists of 11 polished lutetium-yttrium oxyorthosilicate (LYSO) slices measuring 1 × 37.6 × 10 mm3 . The enhanced specular reflector (ESR) was glued on both cross-sectional surfaces of each crystal slice. For the face opposite to the SiPM array and the two end faces of the detectors, surface treatments with and without black paint were implemented for performance comparison. The bottom face of the semi-monolithic detector was coupled to a 4 × 12 SiPM array that was grouped along rows and columns separately into 16 signals. The four row signals were used to identify the slices, and the 12 column signals were used to estimate the y (monolithic direction) and z (depth direction) interaction positions. The detector was irradiated at multiple positions with a collimated 511 keV gamma beam. The collimated beam was obtained with electronic collimation by using a 22 Na point source and a reference detector. The estimated width of the gamma beam is around 0.5 mm. The flood histogram for crystal slices was measured by using the center of gravity (COG) method. The COG method and the squared COG method were used for y position estimation. The standard deviation of the column signals, the ratio of maximum to the sum of the column signals, and the sum of squared column signals were used for z position estimation.RESULTSAll slices were clearly resolved from the measured flood histograms for both detectors with different crystal surface treatments. The estimated y positions roughly linearly change with the true positions at the middle of the detector until ~5 mm from both ends of the detector. The y and z spatial resolutions of the detectors were estimated for all middle positions located more than 5 mm from both ends of the detector. The squared COG method provides better y position resolution than the COG method. The three z estimation methods provide similar depth of interaction (DOI) resolution. Surface treatment with black paint significantly improves both y and z position resolution but degrades the energy and timing resolution of the detectors. The average full width half maxima (FWHM) spatial resolution is improved from 1.77 to 1.07 mm in the y direction by using the squared COG method and from 2.71 to 1.55 mm in the z direction by using the standard deviation method. The slice-based average energy resolution degrades from 15.8% to 24.9%. The timing resolution of the entire detector module degrades from 596 to 788 ps.CONCLUSIONThe performance of rectangular semi-monolithic scintillator PET detectors with two different crystal surface treatments was measured. The detectors provide superior spatial resolution and depth-encoding capability and can be used to develop small animal and dedicated breast and brain PET scanners that can simultaneously achieve high spatial resolution, high sensitivity, and low cost.

First experimental evaluation of count-rate performance for micrometre resolution deep silicon detector

First Experimental Evaluation of a High-Resolution Deep Silicon Photon-Counting Sensor

Timing resolution in double-sided silicon photon-counting computed tomography detectors

A Semi-Monolithic Detector providing intrinsic DOI-encoding and sub-200 ps CRT TOF-Capabilities for Clinical PET Applications

A thick semi-monolithic scintillator detector for clinical PET scanners

Photon-counting CT with silicon detectors: feasibility for pediatric imaging

Scintillation and Cherenkov photon counting detectors with analog silicon photomultipliers for TOF-PET

Design and Optimization of Direct-Conversion Photon-Counting Detector for Dual-Energy Ct Imaging

Performance of Long Rectangular Semi‐monolithic Scintillator PET Detectors

Evaluation of a pixelated large format CMOS sensor for x-ray microbeam radiotherapy

Photon-counting x-ray detectors for CT

A Finely Segmented Semi-Monolithic Detector tailored for High Resolution PET

A depth-encoding PET detector using light sharing and single-ended readout with SiPMs.

Performance of a SiPM Based Semi-Monolithic Scintillator PET Detector

A photon-counting detector for dual-energy breast tomosynthesis

A Depth-Encoding Pet Detector That Uses Light Sharing And Single-Ended Readout With Silicon Photomultipliers

Digital Deconvolution Of Scintillation Detector Signals For High Rate Photon-Counting X-Ray Imaging Applications

The high count rate performance of a two-dimensionally position-sensitive detector for positron emission tomography.

Low power implementation of high frequency SiPM readout for Cherenkov and scintillation detectors in TOF-PET

MiniCACTUS: A 65 ps Time Resolution Depleted Monolithic CMOS Sensor

A High Count-Rate and Depth-of-Interaction Resolving Single Layered One-Side Readout Pixelated Scintillator Crystal Array for PET Applications