Abstract:Square wave alternating current (AC) tungsten inert gas (TIG) welding possesses great advantages in welding stability, quality, flexibility, and cost in manufacturing thin-walled propellant storage tanks with 2219-T6 aluminum alloy. To solve the welding engineering problem of 4 mm-thick plates made by square wave AC TIG welding, we conducted process optimization experiments and performed common microstructure analysis and mechanical property testing. Tensile strength and microhardness reaching 63.8 and 83.1% of the base material appear in the optimal weld. The dendrite morphology, grain size, and eutectic content of all welds were compared and analyzed with optical microscopic observation, image segmentation, and grayscale statistics. The obtained quantitative results interpret the macroscopic properties of the optimal weld from a microscopic perspective. Shallow and uniform equiaxed dimples, evident tearing ridges, and second-phase particles were detected in the tensile fractures. Reticular, granular, and lath eutectic ( α (Al) + CuAl 2 ) were found in the interior and boundaries of dendritic solid solution ( α (Al)). Unexpectedly, the epitaxial growth of the columnar grains was inconspicuous or absent in all welds. Uniform and fine equiaxed grains occupy almost all welds of different process parameters, while the G/R ratio of these welds reaches 15-23 °C·s/mm^2, under which the equiaxed crystals should not have formed. We attributed the grain refinement in these welds to the secondary phase particles in base metal. They are broken into fragments during the multi-pass rolling process of plates, remain semi-dissolved under a fast cooling rate, and provide adequate heterogeneous nuclei for melt solidification. A further SEM and EDS test to base metal and secondary phase particles confirmed our findings and speculations. These results suggest that in the molten pool with sufficient heterogeneous nucleation, the mechanical blocking effect of heterogeneous nucleation may interfere with the thermodynamic effect of welding heat input and speed on grain structure.

Arc characteristics and weld formation of aluminum alloy by AC/DC mixed GTAW

Improvement of the welded joints properties of P460NH steel with AC-assisted GTAW arc

Effect of AC signal ratio on the formation, microstructure and mechanical properties of welded joint of AZ31B Mg alloy during the AC/DC mix GTAW

Study on the weld formation, microstructure and mechanical properties of AZ31B Mg alloy in AC/DC mixed gas tungsten arc welding process

Improvement of microstructure and mechanical properties of stainless steel TIG based wire arc additive manufacturing by using AC/DC mix current waveform

Improvement of the Microstructure and Mechanical Properties of Welded Joint of Wire Arc Additive Manufacturing-AZ31B Magnesium Alloy by Using AC/DC Mixed Current Waveform in Tungsten Inert Gas Welding

Effect of AC/DC mixed current waveform on surface oxidation, microstructure and mechanical properties of TIG welded TC4 titanium alloy

Investigation of arc characteristics and weld formation in ultrasonic-magnetic coaxial hybrid GTAW

Research on Microstructure and Mechanical Properties of Square Wave Alternating Current Tungsten Inert Gas Welded Joints in 2219-T6 Aluminum Alloy

Characteristics of TIG arc-assisted laser welding–brazing joint of aluminum to galvanized steel with preset filler powder

Effect of pulse frequency on microstructure and properties of Ti-6Al-4V by ultrahigh-frequency pulse gas tungsten arc welding

The effects of ultrasonic frequency pulsed arc on wire + arc additively manufactured high strength aluminum alloys

Fluid Flow Characteristics and Weld Formation Quality in Gas Tungsten Arc Welding of a Thick-Sheet Aluminum Alloy Structure by Varying Welding Position

Effect of Current on Mechanical Properties and Microstructure of Aluminum 6061 with Gas Tungsten Arc Welding Process

Preparation and characterization of CMT wire arc additive manufacturing Al-5%Mg alloy depositions through assisted longitudinal magnetic field

Influence of Arc Mode on the Microstructure and Mechanical Properties of 5356 Aluminum Alloy Fabricated by Wire Arc Additive Manufacturing

Enhancing the geometry accuracy and mechanical properties of wire arc additive manufacturing of an Al-5%Mg alloy through longitudinal magnetic field influence

Process Optimization, Microstructure and Mechanical Properties of Wire Arc Additive Manufacturing of Aluminum Alloy by Using DP-GMAW Based on Response Surface Method

Double-Pulse Triple-Wire MIG Welding of 6082-T6 Aluminum Alloy: Process Characteristics and Joint Performances

A New Method for Refinement of Ti-6Al-4 V Prior-Β Grain Structure in the Alternating Magnetic Field Assisted Narrow Gap Gas Tungsten Arc Welding (AMF-GTAW) Via Filler Wire Oscillation

Heat input characteristics and weld bead formation in double-wire double-pulsed GMAW of aluminum alloy under different low-frequency phases