Abstract:A weighting‐factor‐free finite control set predictive torque control (FCS‐PTC) has been developed for induction motor drives by incorporating a hysteresis controller to eliminate stator flux error from the cost function. The tuning of the weighting factor coefficient in FCS‐PTC is critical for improved drive performance. The proposed method regulates the flux by incorporating a separate two level hysteresis controller and torque by the conventional cost function based PTC. The cost function uses torque error only and employs a reduced number of voltage vectors. The reduction of voltage vectors is obtained through the flux hysteresis output and sector determination. The obtained results show comparable dynamic performance of the drive with 43% lower computational burden as compared to conventional PTC. Along with computational benefits, proposed work also demonstrates improved total harmonic distortion (THD) at low speed regions due to the absence of weighting factor in cost function. This work proposes a weighting‐factor‐free finite control set predictive torque control (FCS‐PTC) for induction motor drives by incorporating a hysteresis controller to eliminate stator flux error from the cost function. The tuning of the weighting factor coefficient in FCS‐PTC is critical for improved drive performance. Conventionally, the tuning is based on an intuitive understanding of the dynamical system and empirical methods, which may not yield optimal results. The proposed method regulates the flux by incorporating a separate two‐level hysteresis controller and torque by the conventional cost function‐based PTC. The cost function uses torque error only and employs a reduced number of voltage vectors. The reduction of voltage vectors is obtained through the flux hysteresis output and sector determination. The proposed work is implemented experimentally on the dSpace DS1104 controller board for a two‐level three, three‐phase voltage source inverter‐fed induction motor drive. The experimental results validate the effectiveness of the proposed work under different drive tests compared to conventional PTC and direct torque control (DTC). The obtained results show comparable dynamic performance of the drive with 43% lower computational burden than conventional PTC. Along with computational benefit, the proposed work demonstrates improved total harmonic distortion (THD) at low‐speed regions due to the absence of a weighting factor in the cost function.

Optimal weighting factor design based on entropy technique in finite control set model predictive torque control for electric drive applications

FEA-Based Mathematical Modeling and Simulation for IPMSM Drive with Consideration of Saturation and Cross-Coupling Influence

Hysteresis based predictive torque control without weighting factors for induction motor drives

A Graphical Performance Tool for Design and Comparative Assessment of Predictive Torque Control Methods in Motor Drive Applications

A Graphic Weighting Factor Design Method for Finite Control Set Model Predictive Control of Power Converters

A Review on Weighting Factor Design of Finite Control Set Model Predictive Control Strategies for AC Electric Drives

Model predictive flux control for permanent magnet synchronous motor

Improved weighting factor selection method of predictive torque control for PMSM

A look-up table-based model predictive torque control of IPMSM drives with duty cycle optimization

A novel weighting factor determined method of model predictive torque control for permanent magnet synchronous motor

Model Predictive Thrust Control for Linear Induction Machine: A Fuzzy Optimization Approach

Multi-Objective Optimal Design of High-Speed Surface-Mounted Permanent Magnet Synchronous Motor for Magnetically Levitated Flywheel Energy Storage System

Data-Driven Finite Control-Set Model Predictive Control for Modular Multilevel Converter

Design of Model Predictive Control Weighting Factors For PMSM Using Gaussian Distribution Based Particle Swarm Optimization

Predictive Torque Control for PMSM Based on Weighting Factor Elimination and Fast Voltage Vector Selection

Comparison and analysis of predictive control of induction motor without weighting factors

Optimal Weighting Factor Design of Finite Control Set Model Predictive Control Based on Multiobjective Ant Colony Optimization

Two-Vector-Based Model Predictive Torque Control Without Weighting Factors for Induction Motor Drives

Designing Robust Control for Permanent Magnet Synchronous Motor: Fuzzy Based and Multivariable Optimization Approach

Simple predictive torque control of an open‐end winding interior permanent magnet synchronous motor drive without weighting factor for electric vehicle applications

Improved Finite-Control-Set Model Predictive Control with Virtual Vectors for PMSHM Drives