Abstract:Advanced Li-ion batteries adopting new cathode chemistries are required for the successful widespread transition to electric vehicles (EVs) and renewable energy sources, aiming for high energy density, long cycle life, and good rate capability. Commercial candidates for EV batteries include Ni-rich Li(Ni x Mn y Co 1−x-y )O 2 (NMC) cathodes, with Ni:Mn:Co ratios of 8:1:1 (NMC811) and higher. These are favored because of their high specific capacity (~ 200 mAh g -1 )and reduced cobalt content. Despite all of the advantages, these materials suffer from a range of degradation modes, many of which are associated with the redox and crystallographic behavior at high states of charge. In particular, Ni-rich cathodes suffer from several limitations, such as rapid capacity fade in comparison to NMC stoichiometries with lower Ni content. In addition, they also have a lower onset voltage for oxygen release and subsequent surface reconstruction leading to the formation of spinel and rock salt phases which impede (de)lithiation and therefore the achievable capacity of the cell. 1 Crystallographic properties of electrode materials are intrinsically linked to the electrochemical performance of the cell. NMC materials suffer from anisotropic changes in the crystal structure during cycling which induces strain and leads to issues such as crack formation, expediting degradation. One method to tackle capacity fade is to switch to single-crystal morphologies (particle size 1-3 μm) which have better mechanical stability than conventional polycrystalline morphologies (secondary agglomerate particles ~ 10 μm made up of primary particles which are 100 nm – 1 μm in size) and have less propensity to form extensive rock-salt layers. It is thought that the single-crystal morphology helps to reduce stress in the material as the anisotropic stress in polycrystalline cathodes is concentrated at grain boundaries. However, there is still a limited understanding of the subtle mechanistic differences between the two materials during cycling. 2 A multi-scale approach is required to gain a more comprehensive understanding of the degradation mechanisms at play and how they initiate and propagate. In this work, synchrotron diffraction methods were employed at the crystal, particle and cell scale using a variety of techniques including in-situ Bragg Coherent Diffraction Imaging (BCDI), 3D-XRD and operando high-resolution XRD. Intra-particle, inter-particle and electrode level heterogeneities were observed during cycling, both in pristine and aged samples. It is believed that these heterogeneities accelerate the loss of performance at the cell level by inducing crack formation which can then be observed in X-ray computed tomography data acquired in simultaneous lab studies. The overarching goal of these investigations is to add to the understanding of complex degradation mechanisms for Ni-rich layered transition metal oxide cathodes, ultimately aiding in the informed development of future battery electrode materials. References: 1] Xu, C. et al., Phase Behaviour during Electrochemical Cycling of Ni‐Rich Cathode Materials for Li‐Ion Batteries. Adv. Energy Mater. 2021, 11, 2003404. 2] Yin, S. et al., Fundamental and solutions of microcracks in Ni-rich layered oxide cathode materials of lithium-ion batteries. Nano Energy, 2021, 83, 105854.

Data-driven unlocking volume conservation in single-crystal Ni-rich layered oxides

Enhancing high-voltage performances of nickel-based cathode material via aluminum and progressive concentration gradient modification

Radially Oriented Single‐Crystal Primary Nanosheets Enable Ultrahigh Rate and Cycling Properties of LiNi0.8Co0.1Mn0.1O2 Cathode Material for Lithium‐Ion Batteries

Realizing Superior Cycling Stability of Ni-Rich Layered Cathode by Combination of Grain Boundary Engineering and Surface Coating

Systematic study on anisotropic lattice volume changes in Ni-rich layered oxides: Role of doping and gradient coating

Bulk oxygen release inducing cyclic strain domains in Ni-rich ternary cathode materials

Insights into the Enhanced Cycling Stability of Cobalt-Free Single-Crystal Layered Oxide Cathodes at Elevated Voltage

Unique insights into the design of low-strain single-crystalline Ni-rich cathodes with superior cycling stability

Rational design of surface reconstruction with pinning effect to relieving bulk fatigue for high energy single-crystal Ni-rich cathodes

Enhanced Structure/Interfacial Properties of Single‐Crystal Ni‐Rich LiNi0.92Co0.04Mn0.04O2 Cathodes Synthesized Via LiCl‐NaCl Molten‐Salt Method

Understanding the Degradation Mechanisms of Lithium Ion Batteries Using in-Situ Multi-Scale Diffraction Techniques

In Operando Visualization of Cation Disorder Unravels Voltage Decay in Ni‐Rich Cathodes

Atomic-Resolution In Situ Exploration of the Phase Transition Triggered Failure in a Single-Crystalline Ni-Rich Cathode

Decoupling Capacity Fade and Voltage Decay of Li-rich Mn-rich Cathodes by Tailoring Surface Reconstruction Pathways

Unraveling the Nanoscopic Strain Evolution in Single Crystal Cathodes

Understanding high-temperature cycling-induced crack evolution and associated atomic-scale structure in a Ni-rich LiNi0.8Co0.1Mn0.1O2 layered cathode material

A New Insight into Continuous Performance Decay Mechanism of Ni-rich Layered Oxide Cathode for High Energy Lithium Ion Batteries

Constructing Stable Interface Layer for Boosting High-Voltage Cycling Performance of Single-Crystal Ni-rich Cathodes

Advancements in Addressing Microcrack Formation in Ni–Rich Layered Oxide Cathodes for Lithium–Ion Batteries

Surface Regulation Enables High Stability Of Single-Crystal Lithium-Ion Cathodes At High Voltage

Structural self-reconstruction strategy empowering Ni-rich layered cathodes with low-strain for superior cyclabilities