Abstract:Ni-rich layered cathode materials are important candidates for lithium-ion batteries used for high energy density applications, such as electric vehicles. However, its capacity fades during cycling, especially when a high cut off charge voltage is applied (>4.4 V). To understand the origin of this capacity fade, comprehensive diagnostic tools are applied to understand their structure, chemical and morphological properties during cycling. X-ray diffraction results show that while the LiNi0.6Mn0.2Co0.2O2 (NMC622) can mostly recover its original structure at fully discharged state, even after 0.95 Li is extracted (charged to 5.2 V), it does undergo slab sliding that leads to stacking fault (O1 type) which does not go away during cycling. In addition, transmission X-ray imaging (TXM) results indicate that cycling can induces Li content inhomogeneity within the particle. As a result, the strain builds up and is directly responsible for the cracking of primary and secondary particles. Hard X-ray absorption spectroscopy (XAS) results indicate that both Ni and Co contribute to the capacity by going through the Ni3+/Ni4+ and Co3+/Co4+ redox couples. A comparison is made between Ni-rich and the Li-rich layered materials, which is well known for the problem of oxygen release. It is found that for the Ni-rich system, the oxidization state of transition metals (bulk) are well maintained during cycling, whereas for the Li-rich system the average oxidization states keep decreasing (lower oxidation states at both fully charged and fully discharged states after cycling than the pristine sample), suggesting at least the bulk of Ni-rich material is robust against oxygen release. Soft XAS that differentiates the surface chemical information from the bulk indicates that inactive rock salt phase is formed during cycling. These results show that cycling induced strain, stacking fault and surface reconstruction are the main issues to be addressed for further improvement of this material. Acknowledgement This project was supported by the U.S. Department of Energy, the Assistant Secretary for Energy Efficiency and Renewable Energy, Office of Vehicle Technologies through Advanced Battery Material Research (BMR) program (Battery500 consortium) under Contract No. DESC0012704. This research used resources 8-ID and 28-ID-2 of the National Synchrotron Light Source II, a U.S. Department of Energy (DOE) Office of Science User Facility operated for the DOE Office of Science by Brookhaven National Laboratory under contract no. DE-SC0012704. The authors would also like to acknowledge the use of beamline 6-2c of Stanford Synchrotron Radiation Lightsource, SLAC National Accelerator Laboratory, supported by the U.S. Department of Energy, Office of Science, Office of Basic Energy Sciences under contract no. DE-AC02-76SF00515.

Systematic study on anisotropic lattice volume changes in Ni-rich layered oxides: Role of doping and gradient coating

Enhancing high-voltage performances of nickel-based cathode material via aluminum and progressive concentration gradient modification

Realizing Superior Cycling Stability of Ni-Rich Layered Cathode by Combination of Grain Boundary Engineering and Surface Coating

Mitigation of Cation Mixing of LiNiO2-based Cathode Materials by Li-doping for High-Performing Lithium-Ion Battery

Gradient Boracic Polyanion Doping-Derived Surface Lattice Modulation of High-Voltage Ni-Rich Layered Cathodes for High-Energy-Density Li-Ion Batteries

Data-driven unlocking volume conservation in single-crystal Ni-rich layered oxides

Lanthanum doping and surface Li 3 BO 3 passivating layer enabling 4.8 V nickel-rich layered oxide cathodes toward high energy lithium-ion batteries

Integrated Surface Modulation of Ultrahigh Ni Cathode Materials for Improved Battery Performance

Revisiting the role of Zr doping in Ni-rich layered cathodes for lithium-ion batteries

Micro- and nano-structural design strategies towards polycrystalline nickel-rich layered cathode materials

Lattice Engineering to Refine Particles and Strengthen Bonds of the LiNi 0.9 Co 0.05 Mn 0.05 O 2 Cathode toward Efficient Lithium Ion Storage

New Insight into Microstructure Engineering of Ni‐Rich Layered Oxide Cathode for High Performance Lithium Ion Batteries

Stabilizing effects of atomic Ti doping on high-voltage high-nickel layered oxide cathode for lithium-ion rechargeable batteries

Advancements in Addressing Microcrack Formation in Ni–Rich Layered Oxide Cathodes for Lithium–Ion Batteries

Aluminum and polyanion-doping to improve structural and moisture stability of Ni-rich layered oxides for lithium-ion batteries

Enhancing Surface and Crystal Stability of the Ni-High NCA Cathode for High-Energy and Durable Lithium-Ion Batteries

Relieving strain accumulation in ultra-high Ni cathode to achieve long cycle stability

Reversibility of Ni-Rich Layered Cathode Material Revealed by Structural, Spectroscopic and Imaging Characterizations

Structure modification of Ni-rich layered oxide cathode toward advanced lithium-ion batteries

Recent progress in synthesis and surface modification of nickel-rich layered oxide cathode materials for lithium-ion batteries

Structural Reinforcement through High-Valence Nb Doping to Boost the Cycling Stability of Co-Free and Ni-Rich LiNi 0.9 Mn 0.1 O 2 Cathode Materials