Abstract:Three-dimensional (3D) printing has been increasingly applied to experimental research in geotechnical engineering. In this paper, standard cylinder specimens with high and low strength were prepared using 3D-printing sand core technology. The elastic-plastic and rheological mechanical behaviors were experimentally studied. In addition, the similarity and limitations were verified through comparison with natural sandstone, slate, sand-gypsum, claystone, etc. On this basis, a new way to prepare soft-hard interbedded layered rock in geotechnical mechanics was developed. Considering the features of layered rock and the principle of 3D printing, cylindrical and cubic specimens of soft-hard interlayered rock mass with different inclination angles were prepared by controlling the binder content layer by layer. The deformation and strain differences between the soft and hard phases were verified through digital image correlation. In this case, the anisotropic failure evolution mode of soft-hard interbedded rock mass was revealed by the images captured. The structural anisotropy behaviors of 3D-printed soft-hard interbedded rock was also studied. The results agree well with the published experimental and theoretical results. This study introduces a broad prospect of 3D printing sand core technology for future experimental mechanical research on a soft-hard interbedded layered rock mass in geotechnical engineering. This study developed a new method for preparing soft-hard interbedded rock masses based on 3D printing sand core technology. The elastic-plastic and rheological characteristics of 3D-printed soft rock, hard rock, and soft-hard interbedded rock were investigated and compared with a natural layered rock mass. Moreover, the deformation and strain differences between the soft and hard phases were verified from a mesoscopic perspective. The structural anisotropy behaviors and anisotropic failure mode of soft-hard interbedded rock mass were revealed. The results agreed well with the published experimental and theoretical results. Thus, specimens with complex structures, such as soft-hard interbedded rock mass, could be prepared with 3D printing sand core technology. As a result, the mechanical parameters of 3D-printed specimens were close to those of sandy mudstone and claystone rock masses, while the trends of the stress-strain curves of 3D-printed specimens were consistent with natural sandstone rock masses. This study brings a broad prospect for future investigation of the soft-hard interbedded layered rock mass in actual geotechnical engineering.

Temperature-dependent mechanical properties and crack propagation modes of 3D printed sandstones

Investigation of 3D Printing Sand Core Technology on the Mechanical Behaviors of Soft–Hard Interbedded Rock Masses

Physical and Mechanical Properties and Damage Mechanism of Sandstone at High Temperatures

Pore characteristics and mechanical properties of sandstone under the influence of temperature

The impact of high temperature on mechanical properties and behaviors of sandstone

Microstructure and Mechanical Behavior of 3D Printed Rock-Like Specimens Based on Different Post-Processing Methods

A new method to replicate high-porosity weak rocks subjected to cyclic freezing-thawing: Sand 3D printing and digital image correlation explorations

Investigation on Mechanical Properties Regulation of Rock-Like Specimens Based on 3D Printing and Similarity Quantification

Influence of intermittent opening density on mechanical behavior and fracture characteristics of 3D-printed rock

Mechanical behavior and fracture characteristics of high-temperature sandstone under true triaxial loading conditions

Study on mechanical properties of 3D printed rock mass samples with photosensitive resin material

Experimental Investigation on Dynamic Mechanical Behavior and Fracture Evolution of Fissure-Filled Red Sandstone after Thermal Treatment

Experimental study on changes of pore structure and mechanical properties of sandstone after high-temperature treatment using nuclear magnetic resonance

Experiment study of physical and mechanical properties of sandstone after variable thermal cycles

Mechanical characteristics of sandstone after high temperatures

Study on dynamic fracture properties of sandstone under the effect of high-temperature using large-scale sample

New insights into the effects of low temperatures on the stress-optical properties of printable photopolymers: An experimental investigation

Thermal properties of sandstone after treatment at high temperature

Experimental Investigation of Temperature Effects on the Physical and Mechanical Properties of Red Sandstone

Fracture properties and dynamic failure of three-point bending of yellow sandstone after subjected to high-temperature conditions

Experimental investigation on the fracture surface features of heat-treated red sandstone containing fissure under constant amplitude low cycle impact using 3D digital reconstruction