Abstract:Additive manufacturing (also known as 3D printing) as a fabrication method is ideally suited to merging the organic shapes of human anatomy with engineered components. Many early adopters are exploring the application of these technologies for the fabrication of 3D-printed sockets, but questions remain regarding the ability to fabricate strong, well-fitting definitive sockets. The goal of the present study was to examine the real-world effect of using 3D-printed sockets with regards to mobility, comfort, balance confidence, and user acceptance. Nine veterans with transtibial amputations participated in the study, three each using pin, sealing sleeve, or seal-in liner for suspension. Participants had their conventional definitive socket duplicated using 3D printing. When the 3D-printed socket was ready, using their conventional socket, participants performed a 2-minute walk test, followed by socket comfort score and rating of perceived exertion (10-point scale), Prosthetic Limb Users Survey of Mobility, Activities-Specific Balance Confidence, select subscales of the Prosthesis Evaluation Questionnaire, and the Amputee Body Image Scale–Revised. After completing the baseline data, participants were fitted with the 3D-printed socket and, after using it for 2 weeks, we repeated the data collection. Three participants were not able to complete the study. No large differences were observed for any of the measures. Participants were generally satisfied with the fit of the 3D-printed sockets, but there were challenges with getting the 3D-printed sockets to support elevated vacuum with the sealing sleeve and seal-in liner suspension methods. No differences in performance or user acceptance were identified for pin suspension, but the 3D-printed sockets were not able to reliably support suction or elevated vacuum; further development will be needed before they are ready for clinical application. The present study has demonstrated the ability to achieve satisfactory fit and outcomes using 3D printing to fabricate definitive prosthetic sockets, but the printing method was unable to deliver consistent air-tight sealing for suction or elevated vacuum suspension. Other 3D printing methods and some secondary processing steps may be able to correct this deficiency.

Investigations on 3D Printed Novel Stifel Prosthesis as IoT-Based Solution

On 3D printed novel stifle prosthesis for canines

Histological Evaluation of Osteogenesis of 3D-Printed Poly-Lactic-Co-Glycolic Acid (plga) Scaffolds in A Rabbit Model

3D Printing Surgical Implants at the Clinic: A Experimental Study on Anterior Cruciate Ligament Reconstruction

RF Characterization of a Photocurable PEDOT:PSS:PEGDA Conductive Biomaterial for 3-D-Printing Implantable Antennas

Device Design and Advanced Computed Tomography of 3D Printed Radiopaque Composite Scaffolds and Meniscus

Device Design and Diagnostic Imaging of Radiopaque 3D Printed Tissue Engineering Scaffolds

An Antibacterial-Loaded PLA 3D-Printed Model for Temporary Prosthesis in Arthroplasty Infections: Evaluation of the Impact of Layer Thickness on the Mechanical Strength of a Construct and Drug Release

A preliminary study of the mechanical properties of 3D-printed personalized mesh titanium alloy prostheses and repair of hemi-mandibular defect in dogs

In vivo research on 3D-printed composite PLGA and PDLLA-HA absorbable scaffolds for repairing radius defects in rabbits

Early monitoring for 3D-printed patient-specific mandible reconstructive implant biomechanical behavior under different occlusal conditions using a wireless module system

On 3D printed polyvinylidene fluoride composite-based diaphragmatic hernia sensors

An Insight into the Characteristics of 3D Printed Polymer Materials for Orthoses Applications: Experimental Study

On PVDF composite as partially absorbable smart implants

Patient-Specific Surgical Implants Made of 3D Printed PEEK: Material, Technology, and Scope of Surgical Application

High-Temperature Polylactic Acid Proves Reliable and Safe for Manufacturing 3D-Printed Patient-Specific Instruments in Pediatric Orthopedics—Results from over 80 Personalized Devices Employed in 47 Surgeries

Personalized 3D-printed endoprostheses for limb sparing in dogs: Modeling and in vitro testing

3D printed splint designed by 3D surface scanner for patients with hand allodynia

Point-of-Care 3D Printing: A Feasibility Study of Using 3D Printing for Orthopaedic Trauma

Pilot Test of a Definitive Prosthetic Socket Made with 3D Printing Technology

Multidisciplinary topology and material optimization approach for developing patient-specific limb orthosis using 3D printing