Abstract:The HfOx-based resistive random access memory (RRAM) has been extensively investigated as one of the emerging nonvolatile memory (NVM) candidates due to its excellent memory performance and compatibility with CMOS process. In this study, the influences of deposition ambient, especially the oxygen partial pressure during thin film sputtering, on the resistive switching characteristics are discussed in detail for possible nonvolatile memory applications. The Ni/HfOx/TiN RRAMs are fabricated, and the HfOx films with different oxygen content are deposited by a radio frequency magnetron sputtering at room temperature under different oxygen partial pressures. The oxygen partial pressures in the sputter deposition process are 2%, 4% and 6% relative to engineer oxygen content in the HfOx film. Current-voltage (I-V) measurements, X-ray photoelectron spectroscopy, and atomic force microscopy are performed to explain the possible nature of the stable resistive switching phenomenon. Through the current-voltage measurement, typical resistive switching behavior is observed in Ni/HfOx/TiN device cells. It is found that with the increase of the oxygen partial pressure during the preparation of HfOx films, the stoichiometric ratio of O in the film is improved, the root mean square (RMS) of the surface roughness of the film slightly decreases due to the slower deposition rate under a higher oxygen partial pressure, and the high resistance state (HRS) current decreases. In addition, by controlling the oxygen content of the device, the endurance performance of the device is improved, which reaches up to 10 3 under a 6% oxygen partial pressure. The HfOx films prepared at a higher oxygen partial pressure supply enough oxygen ions to preserve the switching effect. As the oxygen partial pressure increases, the uniformity of the switching voltage is improved, which can be attributed to the fact that better oxidation prevents the point defects (oxygen vacancies) from aggregating into extended defects. Through the linear fitting and temperature test, it is found that the conduction mechanism of Ni/HfOx/TiN RRAM device cells in low resistance state is an ohmic conduction mechanism, while in high resistance state it is a Schottky emission mechanism. The interface between TE and the oxide layer (HfOx) is expected to influence the resistive switching phenomenon. The activation energy of the device is investigated based on the Arrhenius plots in HRS. A switching model is proposed according to the theory of oxygen vacancy conductive filament. Furthermore, the self-compliance behavior is found and explained.

Comment on "Bipolar Resistive Switching in Lanthanum Titanium Oxide and an Increased On/Off Ratio Using an Oxygen-Deficient ZnO Interlayer"

Electrothermal Modeling and Simulation of Resistive Random Access Memory (RRAM) with Different Resistive Switching Oxides

Electric Field Induced Mott Transition and Bipolar Resistive Switching in La2Ti2O7-x Thin Film

Study of the Bipolar Resistive‐switching Behaviors in Pt/GdOx/TaNx Structure for RRAM Application

Oxygen-ion-migration-modulated Bipolar Resistive Switching and Complementary Resistive Switching in Tungsten/indium Tin Oxide/gold Memory Device

Anatomy of Resistive Switching Behavior in Titanium Oxide Based RRAM Device

Performance Enhancement of Nonvolatile Resistive Switching Memory device Made from WO<sub>X</sub>/ZnO Bilayer Structure

Influneces of Different Oxygen Partial Pressures on Switching Properties of Ni/HfOx/TiN Resistive Switching Devices

Ultra-high Resistive Switching Mechanism Induced by Oxygen Ion Accumulation on Nitrogen-Doped Resistive Random Access Memory

Optimization of the Forming Process of HfOx-Based RRAM to Achieve Bidirectional Forming and Enhanced Switching Performance by Inserting an Oxygen-Vacancy-Rich Layer

Improvement of resistive switching characteristics in ZrO2 film by embedding a thin TiOx layer.

Characteristics of the Bipolar Resistive Switching Behavior in Memory Device with Au/ZnO/ITO Structure

Influence of Metal Electrode on the Performance of ZnO Based Resistance Switching Memories

Resistive Switching Characteristics of Resistive Random Access Memory Based on a Ba X Sr 1-X TiO 3 Thin Film Grown by a Hydrothermal Method

Tuning oxygen vacancies and resistive switching properties in ultra-thin HfO2 RRAM via TiN bottom electrode and interface engineering

Spinodal Decomposition-Driven Endurable Resistive Switching in Perovskite Oxides

Physical and Chemical Mechanisms in Oxide-Based Resistance Random Access Memory.

Oxide-based RRAM: Unified microscopic principle for both unipolar and bipolar switching

Transition Metal Oxide Thin Films for Nonvolatile Resistive Random Access Memory Applications

Enhancement of Resistive Switching Performance in Hafnium Oxide (HfO2) Devices via Sol-Gel Method Stacking Tri-Layer HfO2/Al-ZnO/HfO2 Structures

Atomic Layer Deposition of Ga2O3/ZnO Composite Films for High-Performance Forming-Free Resistive Switching Memory.