Abstract:Optimized shape anisotropy of the Fe-Co rich ferromagnetic (α 1 ) phase and the effective separation of the α 1 and α 2 phases with maximum magnetization difference—where α 2 represents a paramagnetic magnetic phase—are the key parameters for maximizing the magnetic properties of Alnico magnets. In this manuscript, efforts have been undertaken to optimize the shape anisotropy of the α 1 phase and increase the difference in magnetization and separation between α 1 and α 2 phases by fine tuning Al and Ni contents, directional solidification and magnetic field annealing methods. At first, Alnico magnets were fabricated by adjusting the content of α 2 phase followed by homogenization, magnetic field annealing at high temperature, and low-temperature tempering. Intrinsic coercivity ( H cj ) of ⁓146.0 kA/m, remanence ( B r ) of ⁓0.90 T and maximum energy density ( (BH) max ) of 46.02 kJ/m 3 are achieved in the magnet with 8.2 wt% Al and 12.8 wt% Ni treated in field of 1.5 T for 10 minutes. At the second stage, the magnet with optimal magnetic properties is directionally solidified to develop columnar grains, and then the α 1 phase is grown in the direction of the columnar grains by magnetic field annealing to enhance the (BH) max to 79.8 kJ/m 3 . The axial ratio of the α 1 phase increased significantly with the increase of the grain size, particularly in the directionally solidified magnets. The Curie temperature of the α 1 phase is noted near 1150 K, while the Curie temperature of the α 2 phase is below 400 K. The magnets demonstrated excellent temperature stability, with magnetic properties decreasing by only 10–12 % at 800 K. These results may pave the way for further development of Alnico magnets specifically for high temperature applications.

Preparation of Alnico magnet with high magnetization by thermal deformation

Refining Alnico 8 magnets with composition optimization of matrix phase, directional solidification and magnetic field annealing

Microstructural and magnetic property evolution with different heat-treatment conditions in an alnico alloy

Structure and Magnetic Study of Ni-Mn-Ga/Al Composite with Modified Magnetocaloric Properties and Enhanced Thermal Conductivity

High-performance Alnico magnets prepared by powder bed fusion

Effect of Electromagnetic Stirring on Fine Grain Formation and Tensile Property Improvement for Fe-Ni Superalloy

Novel Pre-Alloyed Powder Processing Of Modified Alnico 8: Correlation Of Microstructure And Magnetic Properties

Preparing ribbons with core@shell columnar structures and high magnetization using phase transition decomposition mechanism

Microstructure, Magnetism and Critical Behavior of Hot Pressed Ni-Mn-Ga/Al Magnetocaloric Composites with Enhanced Thermal Conductivity and Mechanical Properties

Production of anisotropic hot deformed Nd-Fe-B magnets with the addition of Pr-Cu-Al alloy based on nanocomposite ribbon

Microstructure and magnetic field induced strain of directionally solidified ferromagnetic shape memory CoNiAl alloys

Synthesis, Magnetic and Microstructural Properties of Alnico Magnets with Additives

Effect of spinodal decomposition structure of alnico alloy on magnetic viscosity and magnetization reversal

Microstructure and Magnetic Properties of Alnico Permanent Magnetic Alloys with Zr-B Additives

Deformation indeuced phase seperation of Ni 45Co 5 Mn 36.7In 13.3 alloy at high temperature

Multiscale microstructural evolution of Fe–Ni–Al–Ti alloy with high magnetization

Nanocomposite Didymium-Fe-B/Alnico Magnetic Alloys with Core Shell Structure and Improved Magnetic Properties

Large Magnetocaloric Effect and Magnetoresistance in Fe and Co Co‐Doped Ni‐Mn‐Al Heusler Alloys

Evolution of Fe–Co Rich Particles in Alnico 8 Alloy Thermomagnetically Treated at 800°C

A Study on the Microstructure of Alnico8 Alloy Thermomagnetically Treated at Various Temperatures

Preparation of Anisotropic Nd(Fe,Mo)(12)N-X Magnetic Materials by the Strip-Casting Technique