Abstract:Fretting wear of the stay cable is an important factor affecting the service life of the cable. To accurately calculate the extent of fretting wear, it is necessary to calculate the internal contact pressure in the cable. Although there are many theories and experiments on the contact behavior between wires, there are still no theoretical formulations for calculating the distribution of contact pressure in stay cables. In this paper, by studying the transfer effect of contact pressure in the cable, the PIC (parallel wire cable internal point contact pressure) model for calculating the contact pressure in the parallel wire cable is proposed, considering the effects of wire twisting, sheath compression, and cable bending on the contact pressure. A finite element model corresponding to the contact mode between steel wires is established, and the effectiveness of the PIC model is verified through numerical simulation analysis and a comparison of the existing contact models. The results indicate that contact pressure caused by wire twisting (CWT) is superimposed layer by layer inwards, with the contact pressure increasing closer to the inner layers, and its magnitude is mainly related to the axial tension and twist angle. Simultaneously, on the same layer, contact points along the diagonal experience the greatest contact pressure. Contact pressure caused by sheath compression (CSC) is assumed to conform to the Boussinesq distribution, with the outer layers exhibiting greater contact pressure compared to the inner layers. Contact pressure caused by cable bending (CCB) conforms to the two-dimensional closely arranged contact force transmission model, has a clear layering phenomenon, and the contact pressure within the same layer does not change significantly. The magnitude of the contact pressure is exponentially related to the curvature of the cable and proportional to the tension of the cable, which explains the reason why the slip occurs later for the cables with high tensile forces. Among these three types of contact pressure, CWT is the greatest, followed by CCB, while CSC is the smallest. The theoretical analysis results show that factors such as wire radius, tension, torsion angle, and wire position have an impact on contact pressure. Contact pressure is transmitted along force chains within the cable, following the superposition law between layers. It is uncertain whether slip occurs in the neutral axis or in the outermost layer because of the different distributions of tangential force and interlayer frictional resistance between the layers of wires. Fretting wear simulations of two wires demonstrate that contact pressure has a significant influence on wear patterns, and the “averaging” of contact pressure is a major reason for achieving uniform interface wear. While the contact width increases proportionally with the contact pressure, excessive contact pressure can complicate the problem by changing the contact mode from gross slip to partial slip. This study provides a theoretical method for calculating contact pressures at any contact point within the cables in engineering practice.

Influence of length variation at the transition section of anchor joint on the current-carrying wear property of carbon skateboard/contact wire contacts

Study on the effect of different structural parameters on the wear mechanism in the anchor-segment joint of the rigid overhead catenary

Effect of different gaps in the conductor rail joints on the current-carrying wear performance of carbon skateboards/conductive rail contact

Influence of different arc erosion durations on the wear properties of carbon skateboards/contact wires under low temperature

Experiments and mechanical behaviour of anchorage joints for steel cables

Experimental study of the effect of contact line profiles on the wear mechanism of a skateboard

Sliding Friction and Wear Characteristics of Wire Rope Contact with Sheave under Long-Distance Transmission Conditions

Experimental research on the non-uniform wear of the carbon strip of the metro pantograph

Influence of longitudinal vibration on the friction and wear characteristics of multi-layer winding hoisting wire rope

The Study of Arc Rate, Friction, and Wear Performance of C/C Composites in Pantograph–Catenary System

Evolution Processes of the Tribological Properties in Pantograph/catenary System Affected by Dynamic Contact Force During Current-Carrying Sliding

Fretting Behaviors of Steel Wires with Tensile-Torsional Coupling Force Under Different Wire Diameters and Crossing Angles

A Theoretical Method for Calculating the Internal Contact Pressure of Parallel Wire Cable During Fretting Wear

Influence of Water on the Tribological Behavior of Collector Materials Against Railway Contact Wires at High Sliding Speeds

Effect of the Vibration on Friction and Wear Behavior Between the Carbon Strip and Copper Contact Wire Pair

Study on Current-Carrying Tribological Characteristics of C-Cu Sliding Electric Contacts under Different Water Content

Study on the delamination wear and its influence on the conductivity of the carbon contact strip in pantograph-catenary system under high-speed current-carrying condition

Research on the wear properties of carbon strips and contact wires at frigid temperatures

A comparative investigation into the material matching performance of different friction pairs under current-carrying friction

Friction and Wear Behavior Between Crane Wire Rope and Pulley under Different Contact Loads

Bending Tribo-Corrosion-fatigue Behaviors Between Cable Wire and Saddle Material in the Suspension Bridge