Abstract:In this work, the anisotropic tensile properties of laser additive manufactured (LAMed) GH4169 in as deposited and different heat-treated conditions are presented and the underlying mechanisms are analyzed in detail. Vertical and horizontal specimens for tensile tests were taken from as deposited (AD) and heat-treated blocks. Two heat treatment conditions with solution temperature of 980 °C and 1050 °C were considered. The tensile test results indicate different tensile properties of the vertical and horizontal samples, and such anisotropy is related to heat treatment conditions. The vertical AD sample has higher tensile strength than its horizontal counterpart, while after heat treatment, the horizontal direction shows higher tensile strength. Microstructure characterization, texture and grain morphology analyses were conducted through SEM with EBSD, XRD and TEM observations in order to figure out the main influential factors of the anisotropic tensile properties. Besides, fracture surfaces of the tensile specimens were observed to study the role of precipitates. In addition, the residual stresses in the LAMed samples in AD and heat-treated conditions were measured, and their effects on the anisotropic tensile strength were clarified by correlating the residual stress levels with the recrystallization fractions extracted from EBSD data. The obtained results show that a large number of brittle Laves phases growing along the vertical direction are distributed in the AD samples, which leads to different separation manners of Laves phase/γ matrix interfaces under different loading directions. Besides, the residuals stress level is high direction dependent in the AD samples. After heat treatment, most of the Laves phases are dissolved, and the residual stress experiences a significant variation. On the whole, the anisotropic tensile strength is mainly influenced by the residual stress level before and after heat treatment, and slightly influenced by the dissolution of the Laves phase. The present study provides a deeper understanding of the anisotropic tensile properties of LAMed GH4169, which may contribute to future engineering applications of Ni-based superalloys.

Investigating the Anisotropic Behavior and High-Temperature Mechanical Properties of GH4251 Nickel-Based Superalloy Prepared by Selective Laser Melting and Post Heat Treatment

Mechanical Properties and Fracture Behavior of Laser Powder-Bed-Fused GH3536 Superalloy

In-situ Study of Microstructure and Mechanical Properties of GH3536 Alloy Manufactured by Selective Laser Melting at 750 °C

Influence of Heat Treatment Temperature on Grain Structures and Properties of a Ni-based Superalloy Fabricated Via Selective Laser Melting

An Investigation of the Microstructural Evolution and Tensile Properties of a Nickel-Based GH648 Superalloy Manufactured Through Selective Laser Melting

Effect of Solution Temperature on the Microstructure Evolution and Tensile Properties of GH4175 Superalloy

Experimental Characterization and Strengthening Mechanism of Process-Structure-property of Selective Laser Melted 316 L

Microstructural Evolution and High-Temperature Strengthening Mechanisms of the in 738LC Superalloy Prepared by Selective Laser Melting

Influences of the Γ′ Phase on the Mechanical Properties of a Nickel-Based Single Crystal Superalloy

Effect of Heat Treatment on Microstructure and Residual Stress of GH3536 Superalloy Fabricated by Selective Laser Melting

Effect of Heat Treatment on Microstructure and High Temperature Tensile Mechanical Properties of Selective-Laser-Melted GH3230 Superalloy

Temperature Effects on Deformation Substructures and Mechanisms of a Ni-based Single Crystal Superalloy

Influence of Various Heat Treatments on Microstructures and Mechanical Properties of GH4099 Superalloy Produced by Laser Powder Bed Fusion

A comprehensive study of the anisotropic tensile properties of laser additive manufactured Ni-based superalloy after heat treatment

Effects of Post-Heat Treatment and Carbide Precipitates on Strength-Ductility Balance of GH3536 Superalloy Prepared by Selective Laser Melting

Effect of Post Processing Heat Treatment Routes on Microstructure and Mechanical Property Evolution of Haynes 282 Ni-Based Superalloy Fabricated with Selective Laser Melting (SLM)

High-temperature mechanical properties of nickel-based superalloys manufactured by additive manufacturing

Effect of Heat Treatments on the Microstructure and Mechanical Properties of Ti2AlNb Intermetallic Fabricated by Selective Laser Melting

GH3536 Superalloy Prepared by Selective Laser Melting: Microstructure and Properties

Tailoring the Microstructure and Deformation Mechanisms of an Additively Manufactured Nickel-Based Superalloy by Post-Aging Heat Treatment

Anisotropy in microstructure and mechanical properties of additively manufactured Ni-based GH4099 alloy