Abstract:This work demonstrates the fabrication, mechano-electric, and electrochemical characterisation of a sustainable, fully 3D-printed electrochemical cell (3DPEC) for electroanalytical applications in static and flow conditions. The two-electrode cell comprises carbon black (CB)-filled polylactic acid (PLA) electrodes sealed within insulating PLA walls. The failure behaviour and electric resistance profiles of additive-manufactured multi-material joints with different geometries subjected to tensile load were investigated to explore the possible effect of flow pressure stresses on sensor accuracy. The digital imaging correlation technique was applied to determine the strain distribution during the test. A practical and straightforward route for 3DPEC post-processing treatment was proposed to enhance the electrochemically active surface area (ESA). Finally, we present a proof-of-concept determination of nimesulide, an anti-inflammatory drug, directly in industrial sewage, with a detection limit of 1 nM. The presented approach demonstrates the capability of low-cost, on-demand, and fully customisable 3D-printed cells for rapid environmental screening with high sensitivity.

What problem does this paper attempt to address?

The problem that this paper attempts to solve is to develop a sustainable, fully 3D - printed electrochemical cell (3DPEC) for electroanalytical applications under static and flowing conditions. Specifically, the research focuses on the following aspects: 1. **Mechanical Durability and Electrical Performance**: Explore the influence of flowing pressure stress on the accuracy of the sensor by studying the failure behavior and resistance change of multi - material joints with different geometries under tensile load. Use digital image correlation technology to determine the strain distribution during the test process. 2. **Electrochemical Characterization**: Conduct electrochemical characterization on a 3D - printed two - electrode cell, which consists of a polylactic acid (PLA) electrode filled with carbon black (CB) and an insulated PLA wall. The electrochemical performance of the cell under different conditions was studied, especially its ability to detect nimesulide. 3. **Post - processing Optimization**: A simple and practical post - processing method for 3DPEC was proposed to enhance the electrochemically active surface area (ESA). 4. **Practical Application**: Demonstrated the application of 3DPEC in the direct detection of nimesulide in industrial wastewater with a detection limit of 1 nM. This indicates that low - cost, on - demand, and fully customizable 3D - printed cells have high sensitivity in rapid environmental screening. ### Main Research Contents - **Materials and Preparation**: Use commercial filaments and STL files to manufacture 3DPEC, and optimize the printing parameters and electrochemical pretreatment protocols. - **Mechanical - Electrical Property Testing**: The mechanical strength and electrical properties of multi - material 3D - printed samples were studied through tensile tests, and the strain distribution was analyzed using digital image correlation technology. - **Electrochemical Performance Testing**: Cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) tests were carried out to evaluate the electrochemical performance of 3DPEC. - **Practical Application Verification**: The practical application ability of 3DPEC was verified by using differential pulse voltammetry (DPV) to detect nimesulide in industrial wastewater. ### Key Formulas - **Resistivity Calculation**: \[ \rho = R\cdot\frac{S}{l} \] where \(R\) is the resistance (\(\Omega\)), \(S\) is the cross - sectional area of the conductive path (\(m^{2}\)), and \(l\) is the distance between the electrodes (\(m\)). - **Resistance Change Rate Calculation**: \[ FRC=\frac{\Delta R}{R} \] where \(\Delta R\) is the change in resistance and \(R\) is the initial resistance. - **Strain Factor Calculation**: \[ GF = \frac{FRC}{\epsilon} \] where \(\Delta R\) is the change in resistance, \(R\) is the initial resistance, and \(\epsilon\) is the applied strain. - **ESA Estimation**: \[ i(a,p)=2.99\times 10^{5}\alpha^{1/2}AC_0^{1/2}\nu^{1/2} \] where \(\nu\) is the scanning rate (\(V/s\)), \(\alpha\) is the charge transfer coefficient (set to 0.5), \(A\) is the electrochemically active surface area (\(cm^{2}\)), \(D_0\) is the diffusion coefficient (about \(6.67\times 10^{- 6}cm^{2}/s\) for \([Fe(CN)_6]^{3 - }/^{4 - }\)), and \(C_0\) is the concentration of the electrochemically active compound (\(mol/cm^{3}\)). - **Detection Limit Calculation**: \[ LOD = 3\times\frac{slope}{STD} \] ### Conclusion This research has successfully developed a sustainable, fully 3D - printed electrochemical cell for rapid on - site screening of nimesulide in industrial wastewater. By optimizing the printing parameters and electrochemical pretreatment, the electrochemically active surface area was increased, and the sensitivity and stability of the sensor were enhanced. In addition, the mechanical - electrical characteristics of multi - material joints were also explored, providing an important reference for future design and applications.

Exploring the Mechanical Durability and Electroanalytical Performance of 3D-Printed Multi-Material Sensors for Rapid On-Site Screening of Nimesulide in Industrial Sewage

3D printing for electroanalysis: From multiuse electrochemical cells to sensors

Cost-effective fully 3D-printed on-drop electrochemical sensor based on carbon black/polylactic acid: a comparative study with screen-printed sensors in food analysis

Recycling 3D Printed Residues for the Development of Disposable Paper-Based Electrochemical Sensors

Silver nanoparticles electrodeposited on electrochemically treated 3D sensor for nimesulide monitoring by amperometric detection with flow injection analysis

Sequential cyclic-square-wave voltammetric determination of sulfanilamide and ciprofloxacin in environment water samples using a 3D-printed electrochemical device

Exploring the coating of 3D-printed insulating substrates with conductive composites: a simple, cheap and versatile strategy to prepare customized high-performance electrochemical sensors

Quantifying instant water cleaning efficiency using zinc oxide decorated complex 3D printed porous architectures

3D-printed electrochemical platform with multi-purpose carbon black sensing electrodes

On 3D printed biomedical sensors for non-enzymatic glucose sensing applications

Development of an electrochemical sensor utilizing recycled ABS filaments for 3D printing in the determination of diuron

Integrated multi-material portable 3D-printed platform for electrochemical detection of dopamine and glucose

Enhanced 3D-printed Matrix for Electrocatalytic Detection: A Practical and Simple Electrochemical Platform

Integration of 3D printed Mg2+ potentiometric sensors into microfluidic devices for bioanalysis

Towards Clean and Safe Water: A Review on the Emerging Role of Imprinted Polymer-Based Electrochemical Sensors

Customizable Fabrication Process for Flexible Carbon-Based Electrochemical Biosensors

Immobilizing Nanozymes on 3D printed Metal Substrates for Enhanced Peroxidase-like Activity and Trace-level Glucose Detection

Sustainable plant-wearable sensors for on-site, rapid decentralized detection of pesticides toward precision agriculture and food safety

A miniaturized additive-manufactured carbon black/PLA electrochemical sensor for pharmaceuticals detection

Surfactant assisted synthesis of PrM through M site variants (M = Mo, V, and W) for the electrochemical detection of nonsteroidal anti-inflammatory drug – Nimesulide

3D-printed stereolithographic fluidic devices for automatic nonsupported microelectromembrane extraction and clean-up of wastewater samples