Abstract:Abstract Objective The aim of this study was to investigate the effect of immediate dentin sealing (IDS) technique using universal adhesive under simulated pulp pressure on microtensile bond strength (μTBS) of indirect resin composite restorations and dentin permeability. Materials and Methods Fifty extracted caries-free human third molars were used for specimens' preparation. Each molar's occlusal table was abraded flat and their roots were separated under continuous water cooling. Forty specimens were used for microtensile bond strength test (μTBST) evaluation. The μTBST specimens were randomly assigned to two groups according to the dentin sealing time; Immediate dentin sealing (IDS) and delayed dentin sealing (DDS). Each group was further subdivided into two subgroups according to the adhesive system used for dentin sealing: iBOND self-etch adhesive and GLUMA Bond Universal. All specimens were exposed to simulated pulp pressure for 1 week then restored using computer-aided design/computer-aided manufacturing (CAD/CAM) resin composite blocks. The μTBS was evaluated for all tested subgroups after 24 hours and 6 months of water storage. The remaining 10 teeth were used for the preparation of dentin discs for dentin permeability evaluation. They were divided into two groups according to type of self-etch adhesive used. Fluid filtration rate was evaluated after etching, with smear layer and after adhesive application. Results obtained were statistically analyzed using Shapiro–Wilk test and Weibull analysis. Results Statistically significant difference was recorded between μTBS mean values of both IDS and DDS techniques at 24 hours and after 6 months of water storage. GLUMA Bond Universal adhesive had significantly higher bond strength compared with iBond at both IDS and DDS techniques, but both adhesives showed a significant reduction in the Weibull characteristic strength after 6 months of water storage. Significant reduction in dentin permeability was recorded by both adhesives without any significant difference between them. Conclusions The IDS technique using universal adhesive in self-etch mode is an effective strategy for improving the final bond strength of CAD/CAM resin composite restorations and reducing dentin permeability.

Influence of curing mode and aging on the bonding performance of universal adhesives in coronal and root dentin

Influence of Casein Phosphopeptide-Amorphous Calcium Phosphate Application, Smear Layer Removal, and Storage Time on Resin-Dentin Bonding

Bonding Effectiveness of the Universal Adhesive on Caries-Affected Dentin of Deciduous Teeth

Effect of light-, chemical-, and dual-cured universal adhesives on the internal adaptation of resin composites to pulpal and gingival internal walls

The influence of caries-affected dentin on bonding effect of deciduous teeth

Bond Strength, Microleakage, Microgaps, and Marginal Adaptation of Self-adhesive Resin Composites to Tooth Substrates with and without Preconditioning with Universal Adhesives

Microtensile bond strength, 4-point bending and nanoleakage of resin-dentin interfaces: Effects of two matrix metalloproteinase inhibitors

Effect of curing modes and light-cure times on microtensile bond strength of adhesives

Influence of different immediate dentin sealing strategies on bond strength of indirect resin nanoceramic restorations

Influence of different curing modes on the bonding effectiveness of self-adhesive resin luting cements in combination with universal adhesives

Curing Mode of Universal Adhesives Affects the Bond Strength of Resin Cements to Dentin

Influence of adhesive-composite application modalities on their bonding to tooth structure and resistance of the performed restorations to failure

Effect of adding sodium fluoride and nano-hydroxyapatite nanoparticles to the universal adhesive on bond strength and microleakage on caries-affected primary molars

The effect of dentin adhesive and cure mode on film thickness and microtensile bond strength to dentin in indirect restorations

Impact of Immediate Dentin Sealing Using Universal Adhesive under Simulated Pulp Pressure on Microtensile Bond Strength of Indirect Resin Composite Restorations and Dentin Permeability

[Effect of Curing Modes on Knoop Hardness and Microtensile Bond Strength of Two Dentin Adhesives].

Comparative bonding performance of coronal dentin disks and CAD/CAM resin composite disks for biological restoration: The impact of resin-coating technique

Comparison of Marginal Seal and Tensile Bond Strength of an Alkasite, Zircomer, and Bulk Fill Composite to Carious Affected Primary Molars

Comparative Study of Cementum and Dentin Shear Bond Strength using Resin Composite with Universal Adhesive System and Resin Modified Glass Ionomer

Effect of different preparation designs and material types on fracture resistance of minimally invasive posterior indirect adhesive restorations

Laboratory study and clinical application of adhesive marginal fit of dental hard tissue restorations