Abstract:Abstract This paper presents an experimental study of Cu-Mo alloys prepared by powder metallurgy (PM) method. Also, improving the dispersion and wettability of Mo in the Cu matrix was aimed. Mo particles were added by 0.24, 0.48, 0.73 and 0.97% volume fraction to Cu powder. The mixture was mechanically milled by planetary ball mill at a rotational speed of 140 rpm for 24 h under hydrogen atmosphere, with milling ball size of ∼25 times the size of the metal powders. Liquid acetone was utilized as a process control agent (PCA). Paraffin wax (0.5 wt%) was used to decrease the friction with die during the compaction process. The mixture of the blended powder was compacted at ambient temperature under three different pressures (400, 600 and 800 MPa) and then sintered in a vacuum furnace at 1000 °C for 1 h by a heating rate of 5 °C min −1 . The microstructure examination showed a homogeneous dispersion of Mo particles within the Cu matrix with no evidence of new phases formation during the sintering process. Also, the relative density of samples has been increased by increasing both of Mo content and the compaction pressure. The results revealed that the compaction pressure of 600 MPa was the most suitable pressure as it gave the highest densification. Cu—0.97% volume fraction Mo alloy samples exhibited finer Mo particles with a homogenous distribution in the Cu matrix and well bonding with the Cu particles. The microhardness was increased gradually by increasing Mo wt%, while the compressive strength was decreased by increasing the Mo contents. Both the electrical and thermal conductivities were decreased gradually by the addition of Mo. While the coefficient of thermal expansion (CTE) was decreased by Mo addition.

Enhanced Mechanical Properties of Molybdenum Alloy Originating from Composite Strengthening of Re and CeO2

Effect of CeO_2 on Mechanical Performance of Molybdenum Alloys

Achieving an unprecedented strength-ductility balance of molybdenum alloy by homogeneously distributing yttrium-cerium oxide

The Effect of In-Situ ZrO2 on Compressive Properties of Molybdenum-Rhenium Alloys and Strengthening Mechanism

Second Phase Modification and Strengthening Mechanism of Ceo2 Doped Molybdenum Alloy

The Effects of Refractory Elements on Mechanical Properties in CoCrNiFe Concentrated Solid Solution Alloys Across Different Temperatures

Effect of Sm and Ce content on microstructure and mechanical property of newly developed Mg-Sm-Ce-Mn based alloy

Effects of La and Ce on the Microstructure, Thermal Conductivity and Strength Synergy of the As-Extruded Mg-Mn-RE Alloys

Tensile behavior and microstructure evolution of Mo-14 %Re alloy at room temperature and elevated temperatures

Effects of Ce-rich RE on Microstructure and Mechanical Properties of As-Cast Mg-8Li-3Al-2Zn-0.5Nd Alloy with Duplex Structure

Evaluation of tensile property and strengthening mechanism of Zirconia reinforced molybdenum alloy

Effect of rare earth oxide doping on microstructure and mechanical property of Mo-30 W solid solution alloy

Excellent High-Temperature Strength and Ductility of the ZrC Nanoparticles Dispersed Molybdenum

Revealing the room temperature superplasticity in bulk recrystallized molybdenum

Enhanced Strength-Ductility Synergy in Mg-0.5 wt%Ce Alloy by hot Extrusion

Effect of Ce Addition on Microstructure and Mechanical Properties of ZM21 Magnesium Alloys

Enhancing the Mechanical Properties of Casting Eutectic High Entropy Alloys with Mo Addition

Evaluating compressive property and hot deformation behavior of molybdenum alloy reinforced by nanoscale zirconia particles

Improving the mechanical properties and coefficient of thermal expansion of molybdenum-reinforced copper using powder metallurgy

Microstructure and High Temperature Deformation Behavior of the Mo-ZrO 2 Alloys

Improvement of Tensile Behaviours of a Γ’-Co3（al, W） Strengthened Polycrystalline Co-9Al-4.5W-4.5Mo-2Ta-0.02B Alloy at Room-and Hightemperatures by Doping Ce