Abstract:Ultra-large extrusion ratio is hardly inevitable during porthole die extrusion of miniature complex hollow profile on industrial horizontal extruders. Although batch extrusion of miniature complex hollow profile has been achieved at ultra-large extrusion ratio, their microstructure and mechanical properties are still unclear. To this end, under the extrusion temperature ranging from 400 degree celsius to 480 degree celsius, a 4x4 mm Al-Mg-Si alloy micro heat pipe profile was extruded at an ultra-large extrusion ratio of 137. The grain size and crystal orientation of the profile were obtained by metallographic and electron backscattered diffraction (EBSD) techniques, and further exploration of the microhardness, tensile properties and pressure-resisting performance were conducted. Interestingly, severely weakened extrusion strengthening effect and low sensitivity of microstructure and mechanical properties to extrusion temperature were observed. Compared to the as-cast extrusion billet, the profile exhibits slight grain refinement and improvement in mechanical performance, and the extrusion temperature does not significantly affect the microstructure and mechanical properties. Instead, as the extrusion temperature increases, the recrystallization fraction generally decreases. These abnormal phenomena are inferred from the fact that even at lower extrusion temperatures, an ultra-large extrusion ratio leads to premature dynamic recrystallization (DRX), and more abnormal growth grains are formed in the profile, weakening the mechanical properties. The higher the extrusion temperature, the earlier DRX occurs, generally forming more abnormal growth and dynamic recovery grains.

Effect of Extrusion and Annealing Treatment on Peripheral Coarse Grain Structure and Mechanical Property of an Al-Cu-Li-Mg Alloy Extrusion Profile

Microstructure Evolution and Properties of Mg-9Gd-0.8Al Alloy with Lamellar Phase During Extrusion at Different Temperatures

Effect of Annealing Treatment on the Microstructure and Mechanical Properties of Ultrafine-Grained Aluminum

Effect of annealing treatment on texture evolution, microstructure and mechanical properties of an extruded Mg-Gd-Zn-Zr alloy

A Study on Peripheral Grain Structure Evolution of an AA7050 Aluminum Alloy with a Laboratory-Scale Extrusion Setup

Effect of Extruding Technology on Microstructure and Properties of Al-Li Alloy

Effects of Extrusion Process on Microstructure of Aluminum Profiles with Different Wall Thickness Sections

Effects of Heat Treatment and Pre-Stretching on the Mechanical Properties and Microstructure Evolution of Extruded 2050 Al–Cu–Li Alloy

Effects of Extrusion Ratio on Microstructure and Tensile Properties of an Extruded Al-Fe-Cu Alloy

Effects of annealing treatment on microstructure and tensile behavior of the Mg-Zn-Y-Nd alloy

Effects of Hot Rolling, Intermediate Annealing and Cold Rolling on Microstructure, Texture and Mechanical Properties of an Al-Mg-Si-Cu Alloy

Microstructure and mechanical properties of Al−Mg−Si alloy U-shaped profile

Microstructure and mechanical properties of Mg-Li alloy processed by severe plastic deformation and annealing

Microstructure and Texture Characterization of Superplastic Al-Mg-Li Alloy

Optimization of numerical parameters and microstructure evolution on 2195 Al–Li alloy extrusion process

The Dependence of Final Microstructure, Texture Evolution and Mechanical Properties of Al–Mg–Si–Cu Alloy Sheets on the Intermediate Annealing

Effect of grain size distribution and texture on the cold extrusion behavior and mechanical properties of AZ31 Mg alloy

Evolution of Microstructure and Mechanical Properties of Al-Zn-Mg-Cu Alloy by Extrusion and Heat Treatment

Severely Weakened Extrusion Strengthening Effect in Porthole Die Extrusion of Al-Mg-Si Alloy Miniature Complex Hollow Profile under an Ultra-Large Extrusion Ratio

Effect of Hot Extrusion and Subsequent T6 Treatment on the Microstructure Evolution and Tensile Properties of an Al-6Si-2Cu-0.5Mg Alloy

Effect of extrusion parameters on microstructure and mechanical properties of Mg-0.12Ca-0.08Ba alloy