Abstract:High strength and high conductivity Cu-based materials are key requirements in high-speed railway and high-field magnet systems. Cu-Fe alloys represent one of the most promising candidates due to the cheapness of Fe compared to Cu-Ag and Cu-Nb alloys. The high strength of Cu-Fe alloys primarily relies on the high density of the Cu/Fe phase interface, which is controlled by the co-deformation of the Cu matrix and Fe phase. In this study, our main attention was focused on the deformation behavior of the Fe phase using different scales. Cu-2.5% Fe-0.2% Cr (in weight) and Cu-6% Fe alloys were cast, annealed, and cold drawn into wires to investigate their microstructure and properties evolution. Cu-6% Fe contains Cu matrix and Fe, which become the primary particles in the micrometer scale after solution treatment. Cu-2.5% Fe-0.2% Cr contains Cu matrix and Fe precipitate particles in a nanometer scale after solution and aging treatment. The Fe primary particles were elongated and evolved into ribbons in a nanometer scale while the Fe precipitate particles were hardly deformed even at a drawing strain of 6. The reason for the unchanging characteristics of Fe precipitate particles is due to the size effect and incoherent phase interface of Cu matrix and Fe precipitate particles. The strength of both Cu-6% Fe and Cu-2.5% Fe-0.2% Cr alloys increases with the increase in the drawing strain. The electrical resistivity of Cu-6% Fe gradually increases and that of Cu-2.5% Fe-0.2% Cr keeps almost constant with the increase in the drawing strain.

Effects of Extrusion Ratio on Microstructure and Tensile Properties of an Extruded Al-Fe-Cu Alloy

Microstructure Evolution and Properties of Mg-9Gd-0.8Al Alloy with Lamellar Phase During Extrusion at Different Temperatures

Effect of Alloying Elements and Processing Parameters on Microstructure and Properties of 1XXX Aluminium Alloys

The effects of extrusion ratio and heat treatment on microstructures and tensile properties of a powder metallurgy Fe–22Mn steel

Optimization of numerical parameters and microstructure evolution on 2195 Al–Li alloy extrusion process

Effect of extrusion parameters on microstructure and mechanical properties of Mg-0.12Ca-0.08Ba alloy

Microstructures and mechanical properties of high strength Ti-XAl-2Fe-3Cu alloys fabricated by powder compact extrusion

Microstructure and Properties of Cold Drawing Cu-2.5% Fe-0.2% Cr and Cu-6% Fe Alloys

Effect of Zn/Mg ratio on the microstructure and properties of Al-xZn-2.0Mg-1.0Cu-0.2Zr-yTi ultrahigh-strength aluminum alloy extrusion

Effect of Zn/Mg Ratio on Microstructure and Properties of Cold Extruded Al-xZn-2.4Mg-0.84Cu-0.2Zr-0.25Ti Aluminum Alloy

Influences of Fe Content and Cold Drawing Strain on the Microstructure and Properties of Powder Metallurgy Cu-Fe Alloy Wire

The Effect of Extrusion and Heat Treatment on the Microstructure and Tensile Properties of 2024 Aluminum Alloy

Influence of Extrusion Ratio on Microstructure and Tensile Properties of Mg–Gd–Y–Zn–Zr Alloy

Effects of Fe content on microstructure and properties of Cu–Fe alloy

Changes in microstructure and mechanical properties of 2219 Al alloy during hot extrusion and post-extrusion aging

Effects of Fe addition on the microstructures and mechanical properties of as-extruded Zn-0.2Mg alloys

Effect of Ti content and hot/cold extrusion on microstructure and properties of 2219 heat-resistant aluminum alloy

Effects of Temperature Distribution on Microstructure and Mechanical Properties of Hot Extruded Al–Zn–Mg–Cu Alloy Pipe with Variable Cross-Section

Effects of extrusion ratio and temperature on the microstructure and mechanical properties of Mg–Zn–Yb–Zr extrusion alloys

Effects of extrusion parameters on the microstructure, corrosion resistance, and mechanical properties of biodegradable Mg–Zn–Gd–Y–Zr alloy

Synchrotron X-ray tomography investigation of 3D morphology of intermetallic phases and pores and their effect on the mechanical properties of cast Al-Cu alloys