Abstract:The research on Al–Zn–Mg–Cu alloys mainly focuses on the effects of solution aging and strain rate on the microstructure and properties of the alloy, as well as the flow stress behavior of the alloy. There are few studies on the effects of hot rolling deformation and reduction pass on the microstructure and properties of aluminum alloy. The dislocation density of alloy is affected by changing the rolling deformation, and post-heat treatment improves fine grains segregation and break coarse second phases. The alloys comprehensive mechanical properties are improved by controlling the recrystallization fraction and size. Different shape variable rolling and different passes, optical microscope (OM), field emission scanning electron microscope (SEM) with energy dispersive spectrometers (EDS), X-ray diffractometer (XRD), microhardness tester, and other methods were used to characterize the samples, and simulation of the rolling process analyzed by Deform-3D software. The effects of hot rolling deformation and deformation pass on microstructure and properties of aluminum alloy were also studied. The results show that dynamic recrystallization was beneficial to grain refinement when deformation increases to 40%. The coarse second phase was broken and refined into chains and partially spheroidized to dissolve in the matrix under large deformation. Dislocation density decreased after solution treatment when deformation was less than 80%, and increased after large deformation was 80%. The equivalent strain obtained by numerical simulations increases with the increase of deformation. The maximum equivalent strain was on both sides of the rolling surface, and this area was the most prone to crack in rolling. When the increase of the shape variable, the recrystallization volume fraction increased, and the grain size decreased.

Effects of Hot Rolling, Intermediate Annealing and Cold Rolling on Microstructure, Texture and Mechanical Properties of an Al-Mg-Si-Cu Alloy

The Influence of Warm Rolling Reduction on Microstructure Evolution, Tensile Deformation Mechanism and Mechanical Properties of an Fe-30Mn-4Si-2Al TRIP/TWIP Steel

Recrystallization Behavior and Mechanical Properties of Az31b Alloy During the Hot-Rolling Process

Texture, Microstructure and Mechanical Properties of 6111 Aluminum Alloy Subject to Rolling Deformation

The Dependence of Final Microstructure, Texture Evolution and Mechanical Properties of Al–Mg–Si–Cu Alloy Sheets on the Intermediate Annealing

Revealing the Microstructure Evolution Mechanism and Mechanical Responses of a Novel Al–Zn–Mg–Cu Alloy by Hot Deformation Process

Influence of Asymmetric Rolling on the Microstructure, Texture Evolution and Mechanical Properties of Al–Mg–Si Alloy

Effects of Hot Rolling Processing on Microstructures and Mechanical Properties of Mg–3%Al–1%Zn Alloy Sheet

Microstructure evolution and mechanical properties of Al-Cu-Li alloys with different rolling schedules and subsequent artificial ageing heat treatment

Effect of recrystallization annealing, solid solution and pre-aging intermediate treatment on microstructure and mechanical properties of Al-Mg-Si rolled sheet

Effect of Rolling Reduction on Microstructures and Mechanical Properties of Sc-Containing Al-3.2Cu-1.5Li Alloy

Effects Of Rolling Process On Microstructure And Mechanical Property Of 7050 Aluminum Alloy

Effect of Deep-Cooling Rolling Deformation on the Microstructure and Mechanical Properties of an Al-4.5Cu-1.5Mg-0.6Mn-0.2Ti Alloy

Influence of Annealing Time on Microstructure and Mechanical Properties of Al-14.5Si Alloy Prepared by Super-Gravity Solidification and Cold-Rolling

Effect of rolling deformation and passes on microstructure and mechanical properties of 7075 aluminum alloy

Effect of asymmetric rolling and subsequent ageing on the microstructure, texture and mechanical properties of the Al-Cu-Li alloy

Influence of Asymmetric Rolling Process and Thickness Reduction on the Microstructure and Mechanical Properties of the Al–Mg-Si Alloy

Effect of Rolling Temperature on Microstructure and Properties of Al-Mg-Li Alloy

Effect of cold rolling on microstructure and mechanical properties of a Cu–Zn–Sn–Ni–Co–Si alloy for interconnecting devices

Influence of Different Rolling Processes on Microstructure and Strength of the Al–Cu–Li Alloy AA2195

Effects of intermediate annealing and rolling on plastic failure and grain refinement of Al-Mg-Li alloy