Abstract:The present study assesses RANS-based turbulence models to simulate the isothermal confined swirling flow in a combustor representing a constituent can combustor of the can-annular configuration used in jet engines. The two-equation models (standard k−ε , realizable k−ε , standard k−ω , SST k−ω ), and seven-equation model (linear pressure strain - Reynolds stress model, LPS-RSM), are assessed by comparing their predictions of mean axial velocity, mean transverse velocity, turbulent kinetic energy, and shear stress with the experimental data at two different positions (i.e., the primary and dilution hole planes) in the combustor. While the two-equation models generally have failed to predict the confined swirling flow at both positions accurately, the SST k−ω model yielded the most accurate, followed by standard k−ω and realizable k−ε models. The discrepancies between the computational and experimental results could be attributed to the isotropic turbulence assumptions, which, however, are invalid for confined swirling flows. Further, the two-equation model formulations cannot capture the intricacies of vortex flow and its interaction with the surroundings in confined swirling flows. The LPS-RSM, which considers turbulence anisotropy, showed some promise, although overpredicted results follow the trend with experimental values at the primary holes plane. However, at the dilution holes plane, the model overpredicted the velocity field, and underestimated the turbulence field, including turbulent kinetic energy and shear stress. These observed discrepancies can be ascribed to the pressure-strain correlation in the LPS-RSM, which assumes the pressure is a linear function of the strain-rate tensor. However, this linear assumption is quite simplistic for complex flows. Further, the influence of discretization (SOU and third-order MUSCL) schemes of convective terms is also assessed, and the differences in predictions resulted from MUSCL scheme having lower diffusion and superior ability to capture sharper gradients, however, did not translate into improving the solution accuracy. Hence, this study suggests that more advanced high-fidelity turbulence models (e.g., hybrid RANS-LES, LES, DNS) are needed to accurately predict the confined swirling flow in combustors.

Influence of Turbulence Models on the Numerical Prediction of Flow in an Industrial Gas Turbine Intake System

Effects of inlet turbulence intensity on wall heat transfer in a turbine guide vane

Numerical Simulation of a Turbulence Flow in the Cut-off Valve by RNG k- ε Turbulence Model

Influence of the turbulence model on the numerical predictions of cold turbulent flow in a heavy-duty gas turbine DLN combustor

Effect of Relative Positions between Blade and Volute Tongue on Prediction of Performance in Simulation of Centrifugal Pump

Numerical simulation of 3-D turbulent flows in a cut-off valve and analysis of flow characteristics in pipe

Impact of Inlet Flow Angle Variation on the Performance of a Transonic Compressor Blade Using NIPC

Investigation of turbulence models for aerodynamic analysis of a high-pressure-ratio centrifugal compressor

The Numerical Simulation of Gas Turbine Inlet-Volute Flow Field

Experimental and Numerical Investigation of the Non-Reacting Flow in a High-Fidelity Heavy-Duty Gas Turbine DLN Combustor

Validation and Analyses of QCR Correction Turbulence Model in Sub-/Super-sonic Inner Flows

Investigation on the Performance Prediction of Single-Stage Axial Compressor by Using Different Turbulence Models

Assessment of RANS-based turbulence models for isothermal confined swirling flow in a realistic can-type gas turbine combustor application

Comparison study of turbulence models in numerical simulation of multi-jets impinging injectors

Numerical Investigation on Ultra-High-lift Low-Pressure Turbine Cascade Aerodynamics at Low Reynolds Numbers Using Transition-Based Turbulence Models

Numerical simulation prediction of pressure distribution of guide vanes in a high-head pump turbine

Numerical Analysis of Unstable Turbulent Flows in a Centrifugal Pump Impeller Considering the Curvature and Rotation Effect

Numerical research on the aerodynamic performance of inlet volute duct for a heavy-duty gas turbine

Numerical analysis on flow in pump-turbine in turbine mode at high flow rates

Evaluation of RANS-based turbulence models for isothermal flow in a realistic can-type gas turbine combustor application

Assessment of advanced RANS turbulence models for prediction of complex flows in compressors