Abstract:The poly(ethylene terephthalate) (PET)/isotactic polypropylene (iPP) in situ microfibrillar blends have been prepared through a “slit die extrusion–hot stretch–quenching” process, in which PET assumes microfibrils with 0.5–15μm in diameter depending on the hot stretching ratios (HSR, the area of the transverse section of the die to the area of the transverse section of the extrudate). The injection molded specimens of virgin iPP and the PET/iPP blends were prepared by conventional injection molding (CIM) and by shear controlled orientation injection molding (SCORIM), respectively. The effect of shear stress and PET phase with different shape on superstructures and their distribution of injection molded microfibrillar samples were investigated by means of small angle X-ray scattering (SAXS) and wide angle X-ray scattering (WAXS). The shear (or elongational) flow during CIM and SCORIM can induce oriented lamellae (i.e. kebabs induced by shish). The shish-kebab structure appears not only in the skin and intermediated layers of CIM samples, but also in the whole region of SCORIM samples. For the neat iPP samples, a more “stretched” shish-kebab structure with higher orientation degree can be obtained in the interior region (intermediate and core layers) by the SCORIM method; moreover, the SCORIM can result in the growth of β-form crystal both in intermediate layer and in core layer, which only appears in intermediate layer of the neat iPP samples obtained by CIM. For the PET/iPP blends, interestingly, the addition of microfibrils as well as their aspect ratios can affect the orientation degree of kebabs only in the intermediate layers, and the addition of microfibrils with a low aspect ratio can bring out a considerable increase in the orientation degree of kebabs along the flow direction. However, for the SCORIM, the addition of microfibrils seems to be a minor effect on the orientation degree of kebabs, and it tends to hamper the formation of a more “stretched” shish-kebab structure and suppresses the growth of β-form crystal distinctly. Furthermore, It appears from experiment that γ-form crystals can grow successfully in this oriented iPP melt with the synergistic effect of shear and pressure only when the growth of β crystals can be restrained by some factors, such as the PET dispersed phase and thermal conditions (cooling rate).

Gradient Nanostructure and Its Relationship with the Mechanical Properties of Injection-Molded PBAT Studied Using SAXS-CT

Nondestructive and Quantitative Characterization of Bulk Injection-Molded Polylactide Using SAXS Microtomography

Influence of Structure Gradients in Injection Moldings of Isotactic Polypropylene on Their Mechanical Properties

Study on the influence of in-mold sequential injection molding process parameters on mechanical properties of self-reinforced single composites

Manipulation of Chain Entanglement and Crystal Networks of Biodegradable Poly(butylene Adipate-Co-butylene Terephthalate) During Film Blowing Through the Addition of a Chain Extender: an in Situ Synchrotron Radiation X-ray Scattering Study.

Morphology and Mechanical Behavior of Isotactic Polypropylene with Different Stereo-Defect Distribution in Injection Molding

Investigation on the Morphology and Tensile Behavior of Β‐nucleated Isotactic Polypropylene with Different Stereo‐defect Distribution

The effect of microstructure on the tensile and impact behaviour of short-glass fibre-reinforced polyamide 6.6 as assessed by micro-computed tomography

Crystallinity and mechanical properties of polypropylene products foamed by microcellular injection molding process

Shear Enhanced Crystallization and Tensile Behaviors of Oscillation Shear Injection Molded Poly(ethylene Terephthalate)

Crystalline Morphology of Isotactic Polypropylene (ipp) in Injection Molded Poly(Ethylene Terephthalate) (pet)/ipp Microfibrillar Blends

Understanding process-structure-property relation for elastoplastic behavior of polymer nanocomposites with agglomeration anomalies and gradient interphase percolation

High-Throughput in Situ Characterization of Polymer Crystallization under an Intense Flow, High Pressure, and Cooling Gradient during Injection Molding

Dependence of microstructure and properties of polypropylene/bromo‐isobutylene‐isoprene rubber thermoplastic vulcanizates on the molding process

Morphological Structure and Mechanical Properties of a Nucleated Polyoxymethylene (POM) Homopolymer Resin Processed Under Conventional Injection Molding Conditions

Crystalline Structure Of Injection Molded Beta-Isotactic Polypropylene: Analysis Of The Oriented Shear Zone

Effect of molding on the structure and properties of poly(butylene adipate-co-terephthalate)/poly(propylene carbonate)/organically modified montmorillonite nanocomposites

Effect of Rapid Mold Heating on the Structure and Performance of Injection-Molded Polypropylene

Influence of Preparation Methods on the Structures and Properties for the Blends Between Polyamide 6co6t and Polyamide 6: Melt‐mixing and In‐situ Blending

Mechanical properties and structural characteristics of PP/PP-g-SBR nanocomposites prepared by dynamical photografting

The morphology evolution and crystallization behavior of microinjection molded polyoxymethylene/molybdenum disulfide nanocomposite