Abstract:The geometric parameters and stress conditions of fractures are the main factors that determine the strength and deformation characteristics of fractured rock masses, and the ultimate instability and failure of fractured rock masses are caused by the extension and penetration of the structural plane. In this study, a series of Φ50 × 100 mm standard cylinder specimens were prepared to simulate brittle rock masses. The uniaxial compressive strength and tensile strength of the specimens were 33 and 2.8 MPa, respectively. Non-persistent fractures with different inclination angles, connectivity rates, openings, spacings, groups, and roughness were prefabricated in the specimens, and the fractures were filled with plasticine. Furthermore, the crack propagation and failure mechanisms of filled fractured rock masses under uniaxial compression (the loading rate is 0.2 MPa/s) were analyzed by a 3D video image correlation system. Comparing the results of this research with those of previous researches, and combining with relevant theoretical analysis, the following conclusions are drawn: (1) the curve of the peak strength reduction coefficient k σ of the specimen with the fracture inclination angle α is roughly V-shaped, and being the smallest when the fracture inclination angle α is 45°; the reduction coefficient k is monotonically decreasing with the three groups of fracture geometric parameters of spacing b , connectivity rate μ , and opening d , and the peak strength reduction coefficient k σ of the specimen is typically smaller than the elastic modulus reduction coefficient k E . (2) The post-peak stress–strain curve of the specimen with filled fractures is relatively slow, and the plasticity is obviously enhanced. The geometric parameters of the fractures are important factors affecting the change of the mechanical properties of the specimen. The influence degree of different fractures geometric parameters on rock masses mechanical properties is as follows: fracture sets > spacing > connectivity rate > inclination angle > opening > roughness. (3) Due to the concentration of stress, cracks first initiate from the fracture tips, then propagate parallel to the loading direction, and ultimately coalesce between the fractures and the specimen surface. During the failure process of the specimens, four types of cracks were observed: tensile cracks, shear cracks, wing cracks, and reverse wing cracks, with wing cracks dominating crack propagation. (4) Compared with the specimens with unfilled fractures, the stress concentration at the filled fractures was reduced, and more microcracks with higher dispersion developed around the filled fracture.

Experimental Investigation on Mechanical Behaviors and Damage Evolution of Soft Rock Analog Containing Internal Fracture Network

Cracking Behavior and Acoustic Emission Characteristics of Rock Containing a Single Preexisting Flaw

Experimental investigation on mechanical, acoustic, and fracture behaviors and the energy evolution of sandstone containing non-penetrating horizontal fissures

Experimental Study on Mechanical Behavior, Fracture Characteristics, and Acoustic Emission Damage Characteristics of Sandstone Under Triaxial Multistage Stress Disturbance

Influence of intermittent opening density on mechanical behavior and fracture characteristics of 3D-printed rock

Study on multi-scale damage and failure mechanism of rock fracture penetration: experimental and numerical analysis

Experimental and Numerical Study on Mechanical and Fracture Behavior of Rock-Like Specimens Containing Pre-Existing Holes Flaws

Experimental and numerical studies of brittle rock-like specimens with unfilled cross fissures under uniaxial compression

Experimental study on the spatial fracture behaviour of red sandstone containing weak inclusions with non-unitary geometric features under uniaxial compression

Experimental Study on the Effects of Geometric Parameters of Filled Fractures on the Mechanical Properties and Crack Propagation Mechanisms of Rock Masses

Effect of fractures on mechanical behavior of sand powder 3D printing rock analogue under triaxial compression

Acoustic-Mechanical Responses of Intact and Flaw-Contained Rock Deformation under Uniaxial Compression: A Comparison

Experimental and numerical study of failure characteristics of brittle rocks with single internal 3D open-type flaw

Sensitivity Analysis of Fracture Geometry Parameters on the Mechanical Behavior of Rock Mass with an Embedded Three-Dimensional Fracture Network

Experimental and numerical modeling of deformation-cracking mechanics of 3D-printed rock samples with single fracture

Experimental study on fracture characteristics of rock-like material with prefabricated cracks under compression shear

Experimental Investigation of Pre-Flawed Rocks under Dynamic Loading: Insights from Fracturing Characteristics and Energy Evolution

Fracture behavior of cylindrical sandstone specimens with two pre-existing flaws: experimental investigation and PFC3D simulation

Experimental Study on Mechanical Properties, Acoustic Emission Energies and Failure Modes of Pre-cracked Rock Materials under Uniaxial Compression

Experimental Study on Evaluating Fracture Processes of Different Rocks Using Multiple Physical Parameters

Discrete Element Study on the Mechanical Behavior of Flawed Rocks under Dynamic Compression