Abstract:Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture, Ahead of Print. Polyethylene (PE) is one of the most widely used thermoplastics in the polyolefin family. Despite its numerous applications in the industry, particularly in packaging, 3D printing with PE has been a significant challenge that has received little attention. The main obstacles to successful 3D printing with PE are high shrinkage, weak adhesion to the print bed, and weak interlayers. This paper addresses this problem by introducing Polyolefin Elastomer (POE) as an additive in the 3D printing process. Three different POE-LDPE compounds with varying LDPE weight percentages (90%, 70%, and 50%) were 3D printed and analyzed for their mechanical and microstructural properties. The POE and LDPE were blended using the melt mixing method, and the resulting POE-LDPE granules were directly used as input for the FDM machine. The 3D-printed samples were then subjected to DMTA, tensile, compression tests, and SEM imaging. The DMTA results showed that the glass transition temperature of all three samples fell within the range of 71°C to 78°C. Increasing the POE content and decreasing the LDPE amount from 90% to 50% led to a decrease in the storage modulus. In terms of the tensile test results, it was observed that reducing the LDPE amount and increasing the POE content had a toughening effect on the samples, improving their formability and elongation from 1566% for POE-90wt% LDPE to 2112% and 2829% for POE-70wt% LDPE and POE-50wt% LDPE respectively. However, the tensile strength decreased with an increase in the POE amount. For POE-90wt% LDPE, the tensile strength was 14.06 MPa, and for POE-90wt% LDPE, it was just below 13.96 MPa. The compression test revealed that the addition of POE weakened the yield strength of the samples. SEM images demonstrated that the printability of the 3D-printed POE-LDPE samples decreased as the LDPE amount decreased and the POE amount increased. The images also revealed single-phase and miscible blends. These findings suggest the potential emergence of a new, affordable, biocompatible, and recyclable raw material for 3D printing.

Dynamic Mechanical and Thermal Analysis of 3D-Printed ABS/POE Blends for Tunable Mechanical Properties

Mechanical, thermal, and microstructure analysis of 3D printed polyolefin elastomer-acrylonitrile butadiene styrene blends for tunable mechanical properties

The effect of Polyolefin elastomer on the 3D printing properties of Acrylonitrile butadiene styrene, Polyethylene, and Polypropylene

Assessment of the mechanical properties of PC/ABS blends for functional prototyping by FFF 3D printing

Flexure Behaviors of ABS-based Composites Containing Carbon and Kevlar Fibers by Material Extrusion 3D Printing

Influence of Layer Thickness and Raster Angle on the Mechanical Properties of 3D-Printed PEEK and a Comparative Mechanical Study between PEEK and ABS

Three-dimensional printing with waste acrylonitrile butadiene styrene: Processing and characterization

Mechanical and Thermal Properties of Abs/Montmorillonite Nanocomposites for Fused Deposition Modeling 3d Printing

Assessment of Physio-Mechanical characteristics of ABS/PETG blended parts fabricated by Material Extrusion 3D printing

Influence of LLDPE on the mechanical properties improvement of 3D printed POE/LLDPE blends

An Investigation of Tensile, Fatigue, and Fracture Behavior of 3D-Printed Polymers

3D-Printable ABS Blends with Improved Scratch Resistance and Balanced Mechanical Performance

Isotropic and Anisotropic Elasticity and Yielding of 3D Printed Material

Optimization of Fused Deposition Modeling Process Parameters and Dynamic Mechanical Analysis of 3D Printed Polycarbonate/Acrylonitrile-Butadiene-Styrene Composite Loaded with Tetrabromobiphenol-A and Microcrystalline Cellulose

Mechanical characterization and experimental modal analysis of 3D Printed ABS, PC and PC-ABS materials

High quality 3D printing of low-density polyethylene blends considering the softening effect of polyolefin elastomer

Study on performance characteristics of fused deposition modeling 3D ‐printed composites by blending and lamination

Effects of FDM-3D printing parameters on mechanical properties and microstructure of CF/PEEK and GF/PEEK

Effect of Fused Filament Fabrication Parameters and Tetrabromobisphenol-A/Microcrystalline Cellulose Additives on the Dynamic Mechanical Behavior of Polycarbonate/Acrylonitrile–Butadiene–Styrene Blends for Precision Structures

Mechanical Properties Optimization of Poly-Ether-Ether-Ketone Via Fused Deposition Modeling.

Investigating the Effect of ABS on the Mechanical Properties, Morphology, Printability, and 4D Printing of PETG‐ABS Blends