Abstract:This study is focused on the importance of nanohydroxyapatite (nHA) particle morphology with the same particle size range on the rheological behavior of polycaprolactone (PCL) composite ink with nHA as a promising candidate for additive manufacturing technologies. Two different physiologic-like nHA morphologies, that is, plate and rod shape, with particles size less than 100 nm were used. nHA powders were well characterized and the printing inks were prepared by adding the different ratios of nHA powders to 50% w/v of PCL solution (nHA/PCL: 35/65, 45/55, 55/45, and 65/35 w/w%). Subsequently, the influence of nHA particle morphology and concentration on the printability and rheological properties of composite inks was investigated. HA nanopowder analysis revealed significant differences in their microstructural properties, which affected remarkably the composite ink printability in several ways. For instance, adding up to 65% w/w of plate-like nHA to the PCL solution was possible, while nanorod HA could not be added above 45% w/w. The printed constructs were successfully fabricated using the extrusion-based printing method and had a porous structure with interconnected pores. Total porosity and surface area increased with nHA content due to the improved fiber stability following deposition of material ink. Consequently, degradation rate and bioactivity increased, while compressive properties decreased. While nanorod HA particles had a more significant impact on the mechanical strength than plate-like morphology, the latter showed less crystalline order, which makes them more bioactive than nanorod HA. It is therefore important to note that the nHA microstructure broadly affects the printability of printing ink and should be considered according to the intended biomedical applications.

Influence of Particle Size Distribution on Hydroxyapatite Slurry and Scaffold Properties Fabricated Using Digital Light Processing

Effect of Foreign Ion Substitution and Micropore Tuning in Robocasting Single-Phase Bioceramic Scaffolds on the Physicochemical Property and Vascularization

Additive manufacturing of hydroxyapatite bioceramic scaffolds: Dispersion, digital light processing, sintering, mechanical properties, and biocompatibility

Study of falling‐down‐type DLP 3D printing technology for high‐resolution hydroxyapatite scaffolds

3D printing of hydroxyapatite scaffolds with good mechanical and biocompatible properties by digital light processing

High performance hydroxyapatite ceramics and a triply periodic minimum surface structure fabricated by digital light processing 3D printing

Evaluation of the Morphological Effects of Hydroxyapatite Nanoparticles on the Rheological Properties and Printability of Hydroxyapatite/Polycaprolactone Nanocomposite Inks and Final Scaffold Features

Lipids in blood-brain barrier models in vitro II: Influence of glial cells on lipid classes and lipid fatty acids

Effects of particle size of hydroxyapatite on mechanical property and cytocompatibility of hydroxyapatite/poly(amino acid) composites

Sol-Gel Synthesis and Characterisation of Nano-sized Hydroxyapatite Powders and Hydroxyapatite/ Poly(D,L-lactide-co-glycolide) Composite Scaffolds

Morphologies, mechanical and in vitro behaviors of DLP-based 3D printed HA scaffolds with different structural configurations

Surface modification of hydroxyapatite and its influences on the properties of poly(lactic acid)-based porous scaffolds

Effect of reactive diluent concentration on rheological and curing behavior of zirconia ceramic slurry for DLP printing

Influence of size and crystallinity of nanohydroxyapatite (nHA) particles on the properties of Polylactic Acid/nHA nanocomposite scaffolds produced by 3D printing

Digital light processing (DLP) of nano biphasic calcium phosphate bioceramic for making bone tissue engineering scaffolds

Powder Loading Effects on the Physicochemical and Mechanical Properties of 3D Printed Poly Lactic Acid/Hydroxyapatite Biocomposites

Development of hybrid 3D printing approach for fabrication of high-strength hydroxyapatite bioscaffold using FDM and DLP techniques

Additive Manufacturing of Hydroxyapatite Bioceramic Scaffolds with Projection Based 3D Printing

Functionally Graded Triply Periodic Minimal Surface Scaffold of HA-Al 2 O 3 via Vat Photopolymerization 3D Printing

Particle size distribution effects on physical properties of injection molded HA/PLA composites

Morphology, mechanical properties, and mineralization of rigid thermoplastic polyurethane/hydroxyapatite scaffolds for bone tissue applications: effects of fabrication approaches and hydroxyapatite size