Abstract:Producing micro and macroporous 3D structures that mimic the bone architecture of a specific anatomic region, namely the rounded trabeculae in trabecular bone, is a considerable challenge, to which additive manufacturing can make a fundamental contribution. The main objective of the work was to explore the Digital Light Processing (DLP) technique in obtaining customized parts, from a ceramic suspension composed of two different materials, specifically alumina and hydroxyapatite (HA), with a trabecular bone architecture, using Computer Assisted Design (CAD) modelling techniques and additive manufacturing. Hydroxyapatite (HA) was added to the alumina matrix to improve the biocompatibility and bioactivity of the composites after sintering. After optimizing all printing parameters and the suspensions rheological properties, samples in alumina and alumina-hydroxyapatite with the desired architecture were obtained. The influence of the incorporation of hydroxyapatite in the alumina formulations was also analyzed, with increasing hydroxyapatite contents: 5, 10, and 15 wt%. The rheological behaviour of the suspensions was studied in a plate-to-plate system. The physical-chemical and mechanical characterization of produced samples were carried out by X-ray diffraction, Scanning electron microscopy, and compressive tests. The suspensions prepared with two different materials showed adequate viscosity to achieve a good spread and homogeneous layers in the 3D printing process. In the produced samples, the occurrence of a hibonite phase (CaAl12O19), resulting from the reaction between alumina and hydroxyapatite during the sintering step, increased the compressive strength of the samples. The high temperature needed for sintering alumina led to the conversation of HA into TCP. The achieved mechanical strength results from the porosity level and the thickness of the struts of the printed architecture. DLP showed to be a precision printing technology of low cost that can be used to fabricate parts in the industry from a suspension composed of a mixture of alumina and HA powders, which is very useful in the bone repair field and not previously reported.

Study of falling‐down‐type DLP 3D printing technology for high‐resolution hydroxyapatite scaffolds

3D printing of hydroxyapatite scaffolds with good mechanical and biocompatible properties by digital light processing

High performance hydroxyapatite ceramics and a triply periodic minimum surface structure fabricated by digital light processing 3D printing

Dlp 3d Printing Porous Beta-Tricalcium Phosphate Scaffold By The Use Of Acrylate/Ceramic Composite Slurry

DLP 3D printing porous β-tricalcium phosphate scaffold by the use of acrylate/ceramic composite slurry

Development of hybrid 3D printing approach for fabrication of high-strength hydroxyapatite bioscaffold using FDM and DLP techniques

Morphologies, mechanical and in vitro behaviors of DLP-based 3D printed HA scaffolds with different structural configurations

Additive Manufacturing of Hydroxyapatite Bioceramic Scaffolds with Projection Based 3D Printing

High resolution DLP stereolithography to fabricate biocompatible hydroxyapatite structures that support osteogenesis.

Additive manufacturing of hydroxyapatite bioceramic scaffolds: Dispersion, digital light processing, sintering, mechanical properties, and biocompatibility

Influence of Particle Size Distribution on Hydroxyapatite Slurry and Scaffold Properties Fabricated Using Digital Light Processing

Additive manufacturing of ceramic alumina/calcium phosphate structures by DLP 3D printing

3D printing of hydroxyapatite/tricalcium phosphate scaffold with hierarchical porous structure for bone regeneration

Deformation Monitoring and Stress Distribution Prediction of 3D-Printed Hydroxyapatite Scaffolds

DLP Fabricating of Precision GelMA/HAp Porous Composite Scaffold for Bone Tissue Engineering Application

Fabrication and Biological Evaluation of 3D-Printed Calcium Phosphate Ceramic Scaffolds with Distinct Macroporous Geometries Through Digital Light Processing Technology.

Zirconia toughened hydroxyapatite biocomposite formed by a DLP 3D printing process for potential bone tissue engineering

Effects of Dispersant Concentration on the Properties of Hydroxyapatite Slurry and Scaffold Fabricated by Digital Light Processing

Nano-Hydroxyapatite Bone Scaffolds with Different Porous Structures Processed by Digital Light Processing 3D Printing

Development of three-dimensional printing polymer-ceramic scaffolds with enhanced compressive properties and tuneable resorption

Physicochemical Properties of 3D-Printed Polylactic Acid/Hydroxyapatite Scaffolds