Abstract:Concrete-filled steel tubes (CFST) incorporating high-strength steel (HSS) could produce more efficient structural system with lighter weight and higher capacity. However, the design methods for applying concrete-filled highstrength steel tubes (CFHST) are not available yet and limited investigations had been reported. In this research, 8 full scale mid-slenderness circular CFHST specimens, made of innovative high-performance Q460qENH structural steel with actual yielding stress fy as high as 530 MPa, were tested subject to axial and eccentric compression. The main parameters considered in the experimental program included: (a) infilled concrete strength fc' = 39.8-75.3 MPa and (b) loading eccentricity ratio e/D = 0-0.3. The numerical model for CFHST was established and validated with load-displacement curves, failure modes and neutral axis locations obtained from the 8 experiments. The numerical models were further validated in capacity predictions with 232 axial compressions and compression-bending CFHST experimental data collected from the literature, proved to be generally applicable with fy = 435-835 MPa, xi = 0.5-8.5 and lambda n = 0.07-1.90 in both circular and square sections. Based on the validated numerical models, total 526 simulations were performed to investigate the influence of: (a) higher yielding strength fy and thinner-walled steel tubes; (b) confinement factor xi and (c) normalized slenderness ratio lambda n, on the composite strength fsc and compression-bending (N-M) interaction behavior. Experimental and numerical investigations showed that high strength steel could further improve the CFST capacity with basically no reduction in safety margin and ductility performance, but was in need of design method modifications due to changes in composite mechanism. On this basis, an analytical refined plastic-section equilibrium model (RPE model) was proposed to derive practical N-M interaction design curve with consideration of strength enhancement due to the composition and actual stress distribution at ultimate state. The further proposed general design method for compression-bending CFHST included: (a) formulas of fsc-xi relationship; (b) validated formulas of pure-bending capacity and overall stability inherited from GB 50936; (c) practical design curves of N-M interaction considering the effect of xi and lambda n. By comparing with GB 50936, AISC 360, EC 4 and CECS 28 provisions, the proposed method provided more accurate solutions in capacity predictions of CFHST members.

Compressive Behavior and Design Calculations of CFST Slender Columns with Latticed Annular Steel Part

Behavior of Eccentrically Loaded Large-Scale CFST Slender Columns with Latticed Annular Steel

Numerical Investigation on Compressive Performance of CFST Columns with Encased Built-Up Lattice-Angles

Seismic Behavior of Concrete-Filled Wide Rectangular Steel Tubular (CFWRST) Stub Columns

Behavior and Design of Slender Concrete-Filled Wide Rectangular Steel Tubular Columns under Axial Compression

Axial Compressive Behavior of FRP-confined Square CFST Columns Reinforced with Internal Latticed Steel Angles for Marine Structures

Global Buckling Behavior of CFST Columns with Assembling Errors

Behavior and Design of Concrete-Filled Narrow Rectangular Steel Tubular (CFNRST) Stub Columns under Axial Compression

Analysis of CFRP-confined CFST Columns Reinforced with Steel Angles under Axial Compression

Behaviour and Design Calculations on Very Slender Thin-Walled Cfst Columns

Numerical Analysis on Concrete-Filled Wide Rectangular Steel Tubular (CFWRST) Stub Columns under Axial Compression

Experimental Study on Axial Compressive Behavior of Concrete-Filled Corrugated Steel Tubular Columns

Flexural Behavior of Circular Section Concrete-Filled Steel Tubes with Embedded Latticed Angles

Confinement-based design and behaviour of concrete-filled stiffened steel tubular square slender columns

Test and design of rectangular steel-reinforced concrete-filled stainless steel tubular short columns

Axial compression behavior of prefabricated L-section thin concrete encased steel short columns

Behavior and General Design Method of Concrete-Filled High-Strength Steel Tube (CFHST) Columns

Behavior and design of axially loaded square concrete-filled double steel tubular slender columns

Finite Element Analysis on Behavior of Reinforced Hollow High Strength Concrete Filled Square Steel Tube Short Columns under Axial Compression

Performance of steel-reinforced square CFST stub columns loaded in axial compression: Experiments

Finite element analysis and bearing capacity calculation of cross-shaped CFST columns under compressive load