Abstract:Magnesium alloy AZ91D is used extensively in the automotive industry because of its high strength-to-weight ratio. Typically, components produced using the alloy are required to have good surface finish and to contribute to high productivity but require long cutting times. Cryogenic cooling is an environmentally friendly technology which has been proven to improve cutting tool life and surface finish. This paper presents an investigation on the effects of dry and cryogenic cutting conditions at a high cutting speed regime for milling of magnesium alloy. This study focused on a high-speed regime due to the chips of magnesium alloy being highly combustible and an effective means of decreasing the temperature in the cutting zone was of great concern. The machining experiment was carried out using uncoated carbide end milling utilizing a full factorial design (L16) with cutting speeds of 900 m/min and 1300 m/min, feed rate of 0.02 mm/tooth and 0.05 mm/tooth, axial depth of cut at 0.2 mm and 0.3 mm, and radial depth of cut at 10 mm and 40 mm. For dry machining, the longest tool life at flank wear (VBmax) of 0.21 mm was at 30 min, which was obtained at cutting speeds of 1300 m/min, feed rate of 0.02 mm/tooth, axial depth of cut at 0.2 mm, and radial depth of cut at 40 mm. Using this cutting condition, a mirror-like surface of 0.106 μm was produced. For machining under cryogenic condition at VBmax of 0.2 mm, the maximum tool life of 1864 min was achieved at a cutting speed of 900 m/min, feed rate of 0.02 mm/tooth, axial depth of cut of 0.3 mm, and radial depth of cut of 40 mm. Under this cutting condition, a lower surface finish of 0.091 μm was obtained. It can be concluded that the application of liquid nitrogen (LN2) is very effective in enhancing the tool life and in obtaining a better-machined surface, especially at a lower cutting speed of 900 m/min. A longer tool life and high-quality machined parts will significantly improve the productivity and cost savings in the related industry.

An Investigation on Tool Performances in Milling Rare-Earth Magnesium Alloys

Milling machinability analysis of GW63K rare-earth magnesium alloys based on the concept of clean cutting

Wear Behavior of Different Coated Tools in MQL-assisted Milling of Magnesium-Based Rare-Earth Alloys

Wear behavior of different coated tools in MQL-assisted high-speed milling of magnesium-based rare-earth alloys

Numerical Study of the Effects of Tool Parameters on the Cutting Temperature Distribution and Ignition Risks of Magnesium Alloys

Comparative Study on Milling Performances of Rare-earth Magnesium Alloys under Dry and MQL Conditions

Investigation and Application of Excellent Performance Mg Rare Earth Alloys As a Structural Material

Experimental Investigation on Machinability of Aluminum Alloy during Dry Micro Cutting Process Using Helical Micro End Mills with Micro Textures

Numerical Study of Different Tools in High-Speed MQL Cutting of Aluminum Alloys

Investigation of Machining and Wear Performance of Various Diamond Micro-Grinding Tools

Methodology of Chip Temperature Measurement and Safety Machining Assessment in Dry Rough Milling of Magnesium Alloys Using Different Helix Angle Tools

Experimental Study and Parameter Optimization on Sustainable and Efficient Machining GH4169 with Rotating Short Arc Milling Method

A review on wear resistance of Mg alloys: the influence of common rare earth alloying elements and general modification techniques

Analysis of cutting forces and surface quality during micro milling of AZ31B magnesium alloy

Tool wear mechanisms in cold plasma and nano-lubricant multi-energy field coupled micro-milling of Al-Li alloy

Strengthening and Toughening Design and Development of Mg-Rare Earth Alloys

Experimental Investigation on Influence of Engagement Angle and Tool Geometry on Plunge Milling

Cutting performance and coated tool wear mechanisms in laser-assisted milling K24 nickel-based superalloy

Evaluation of milling performance of 50-μm D-shaped carbide tool, polycrystalline diamond-coated carbide tool, and polycrystalline diamond tool

Analysis of tool wear and cutting characteristics in milling of powder metallurgy nickel-based superalloy by various coatings

Sustainable High-Speed Milling of Magnesium Alloy AZ91D in Dry and Cryogenic Conditions